EasyManuals Logo

TEFAL Ultimate Autoclean Manual

TEFAL Ultimate Autoclean
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #12 background imageLoading...
Page #12 background image
9
D
E
EN
F
R
NL
I
T
ES
PT
DA
NO
SV
FI
EL
CS
HU
SK
HR
SL
RO
SR
BG
PL
TR
RU
UK
ET
LV
LT
Warning! Use of an abrasive cloth will damage the self-cleaning
c
oating on the soleplate.
Its exclusive active coating eliminates all impurities that can be
g
enerated under normal conditions of use.
Ironing with an incorrect program can however leave traces that may
r
equire manual cleaning. In this case, it is recommended that you use a
s
oft damp cloth on the still warm soleplate so as not to damage the
c
oating.
Y
our steam iron is fitted with an Ultraglide soleplate (depending on model):
Never use aggressive or abrasive products.
When the soleplate is still warm, wipe with a damp cloth
Storing your iron
- Unplug the iron and wait for the soleplate to cool down.
- Empty the water tank and set the steam control to DRY
- fig. 1.1
. A little water may remain in the tank.
- Wind the cord not too tightly around the heel at the back of the iron.
- Store the iron on its heel.
Environment
Environment protection first !
i Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
If there is a problem?
Note! The steam control position must
necessarily be on STEAM
(fig.1.2)
in order to
r
emove or replace the iron's antiscale rod.
Attention! The use of a scouring pad will cause
d
amage to your soleplate's self-cleaning
coating
(fig.17)
Problem Possible causes Solutions
• Water drips from the
holes in the soleplate.
• You are using the Shot of Steam button too often.
• You have stored the iron horizontally, without
emptying it and without setting it to DRY.
• Wait a few seconds between each use
of the button.
• See the section "Storing your iron".
• Brown streaks come
through the holes in
the soleplate and
stain the linen.
• You are using chemical descaling agents.
• You are using pure distilled/demineralised or
softened water.
• Your linen is not rinsed sufficiently or you have
ironed a new garment before washing it.
• Do not add any descaling agents to
the water in the water tank.
See section “Types of water not to use?”.
• See section "Cleaning the soleplate".
• Ensure linen is rinsed thoroughly to
remove any soap deposits or
chemicals on new garments which
may be sucked up by the iron.
• The soleplate is dirty
or brown and can
stain the linen.
• You have ironed with an unsuitable
programme (temperature too high).
• You are using starch.
• Select the appropriate program.
Refer to the chapter “Clean the
soleplate“
• Spray starch on the underside of the
fabric to be ironed.
• There is little or no
steam.
• The water tank is empty.
• The anti-calc valve is dirty.
• Your iron has a build-up of scale.
• Your iron has been used dry for too long.
• Fill it.
• Clean the anti-calc valve.
• Clean the anti-calc valve and carry out
a self-clean.
• Carry out a self-clean.
• Wait for the soleplate to reach the
correct temperature.
• The soleplate is
scratched or
damaged.
• You have placed your iron flat on a metallic
rest-plate or ironed over a zip.
• You have cleaned your soleplate with an
abrasive or metal pad.
• Always set your iron on its heel.
• Try to avoid ironing over zips.
• Refer to the chapter “Clean the
soleplate”.
• Water is leaking out
through the water
tank cover.
• You have not closed the water tank cover
properly.
• Make sure the water tank cover has
clicked shut.
• Steam or water come
from the iron as you
finish filling the tank.
• The steam control is not set to the DRY
position .
• Check that the steam control is
set to the DRY position .
• The spray and/or shot
of steam do not work.
• The water is empty. • Fill the water.
• Water leaks out of the
front of the iron.
• You have exceeded the level MAX when filling
the water tank.
• Empty the surplus water out of the
water tank.
Name of manufacturer : CALOR S.A.S 3.12 104
220-240V a.c. 2010-2400W
220-240 V a.c. 2185-2600W
50/60Hz
Made in France
If you have any problem or queries, please contact our Customer Relations
team first for expert help and advice.
845 602 1454 - UK / (01) 677 4003 - Ireland
or consult our website - www.tefal.co.uk
1800135516 FV95XX E2_110x154 26/01/15 14:45 Page9

Other manuals for TEFAL Ultimate Autoclean

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TEFAL Ultimate Autoclean and is the answer not in the manual?

TEFAL Ultimate Autoclean Specifications

General IconGeneral
BrandTEFAL
ModelUltimate Autoclean
CategoryIron
LanguageEnglish

Related product manuals