Home
Tektronix
Test Equipment
TDS 340A
Tektronix TDS 340A Technical Reference
4
of 1
of 1 rating
288 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
T
echnical Refer
ence
TDS 340A, TDS 360 & TDS 380
Digital Real-T
ime Oscilloscopes
070-9436-04
This document applies to firmware version 1.05
and above.
W
arning
The servicing instructions are for use by qualified
personnel only
. T
o avoid personal injury
, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
2
Table of Contents
Table of Contents
7
Table 1-1: Warranted Characteristics - Signal Acquisition
20
Table 1-2: Warranted Characteristics - Time Base System
21
Table 1-3: Warranted Characteristics - Triggering System
22
Table 1-4: Power Requirements
22
Table 1-5: Warranted Characteristics - Environmental
23
Table 1-6: Typical Characteristics - Signal Acquisition System
24
Table 1-7: Typical Characteristics - Triggering System
25
Table 1-8: Typical Characteristics - Probe Compensator Output
25
Table 1-10: Nominal Traits - Signal Acquisition System
26
Table 1-9: Typical Characteristics - Data Handling
26
Table 1-11: Nominal Traits - Time Base System
27
Table 1-12: Nominal Traits - Triggering System
27
Table 1-13: Nominal Traits - Display System
28
Table 1-15: Nominal Traits - Power Distribution System
28
Table 1-16: Nominal Traits - Mechanical Characteristics
29
Figure 1-1: Oscilloscope Dimensions
30
Table 1-17: Certifications and Compliances
31
Figure 2-1: a Pop-Up Menu
40
Figure 2-2: Using Menus
41
Figure 3-1: Block Diagram
45
Figure 3-2: Block Diagram with Option 14 Installed
46
Figure 4-1: Menu Locations
62
Table 4-1: Test Equipment
63
Figure 4-2: Verifying Adjustments and Signal Path
66
Figure 4-3: Hookup for Functional Test
67
Figure 4-4: Hookup for File System Functional Test
69
Figure 4-5: Hookup for DC Voltage Measurement Accuracy Check
72
Table 4-2: DC Accuracy
73
Figure 4-6: Hookup for Analog Bandwidth Check
74
Figure 4-7: Measuring Analog Bandwidth
75
Figure 4-8: Hookup for Sample Rate Check
76
Figure 4-9: Hookup for Trigger Sensitivity Check
78
Figure 4-10: Measuring Trigger Sensitivity
79
Figure 4-11: Hookup for Sine Wave Generator Leveling
81
Table 5-1: Adjustment Equipment
84
Figure 5-1: the System Calibration Menu
85
Figure 5-2: Timing Compensation Waveform
87
Figure 5-3: Attenuator Adjustment Setup and Locations
88
Figure 5-4: Monitor Adjustments
90
Table 6-1: External Inspection Check List
95
Table 6-2: Internal Inspection Check List
96
Figure 6-1: Oscilloscope Orientation
98
Table 6-3: Tools Required for Module Removal
98
Figure 6-2: Line Cord Removal
100
Figure 6-3: Line Fuse Removal
101
Figure 6-4: Knob and Shaft Removal
102
Figure 6-5: Rear Cover, Cabinet, and Cabinet Handle and Feet Removal
104
Figure 6-6: Removing the Disk Drive
105
Figure 6-7: Trim Ring, Menu Elastomer, and Menu Buttons Removal
106
Table 6-4: Power Supply Secondary Voltages
136
Td3F14A
146
Other manuals for Tektronix TDS 340A
User Manual
164 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Tektronix TDS 340A and is the answer not in the manual?
Ask a question
Tektronix TDS 340A Specifications
General
Brand
Tektronix
Model
TDS 340A
Category
Test Equipment
Language
English
Related product manuals
Tektronix TDS 340
65 pages
Tektronix TDS 360
65 pages
Tektronix TDS 684A
303 pages
Tektronix TDS 520D
376 pages
Tektronix TDS 620A
382 pages
Tektronix TDS 520B
303 pages
Tektronix TDS 500D
376 pages
Tektronix TDS 520A
291 pages
Tektronix TDS 410A
291 pages
Tektronix TDS 500C
352 pages
Tektronix TDS 700A
303 pages
Tektronix TDS Series
394 pages
To Next PageTo Next Page
Need help?
General
