Tektronix TDS 520D - Page 7

Table of Contents
ii
TDS 500D, TDS 600C, TDS 700D & TDS 714L Performance Verification and Specifications
List of Figures
Figure 1–1: Map of display functions 1–3. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–2: Verifying adjustments and signal-path compensation 1–6. .
Figure 1–3: Universal test hookup for functional tests – TDS 600C
shown 1–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–4: Measurement of DC offset accuracy at zero
setting – TDS 684C shown 1–37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–5: Initial test hookup 1–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–6: Measurement of DC accuracy at maximum offset
and position 1–41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–7: Initial test hookup 1–43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–8: Optional initial test hookup 1–43. . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–9: Measurement of analog bandwidth 1–46. . . . . . . . . . . . . . . . . .
Figure 1–10: Initial test hookup 1–49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–11: Measurement of channel delay – TDS 684C shown 1–51. . . .
Figure 1–12: Initial test hookup 1–53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–13: Measurement of accuracy – long-term and delay time 1–55.
Figure 1–14: Delta time accuracy test hookup 1–56. . . . . . . . . . . . . . . . . . .
Figure 1–15: Initial test hookup 1–60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–16: Measurement of time accuracy for pulse and glitch
triggering 1–61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–17: Initial test hookup 1–64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–18: Measurement of trigger sensitivity – 50 MHz results
shown on a TDS 684C screen 1–65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–19: Initial test hookup 1–68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–20: Measurement of main trigger out limits 1–70. . . . . . . . . . . . .
Figure 1–21: Initial test hookup 1–73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–22: Measurement of probe compensator frequency 1–74. . . . . . .
Figure 1–23: Subsequent test hookup 1–75. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–24: Measurement of probe compensator amplitude 1–76. . . . . .
Figure 1–25: Jitter test hookup 1–78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1–26: Jitter test displayed waveform – TDS 754D shown 1–79. . . .
Figure 1–27: Jitter test when completed – TDS 754D shown 1–80. . . . . . .
Figure 1–28: Triggered signal range test – 300 mV 1–81. . . . . . . . . . . . . . .
Figure 1–29: Triggered signal range test – 75 mV 1–82. . . . . . . . . . . . . . . .
Figure 1–30: 60 Hz Rejection test hookup 1–83. . . . . . . . . . . . . . . . . . . . . .
Figure 1–31: 60 Hz Rejection test setup signal 1–83. . . . . . . . . . . . . . . . . . .
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com