Tektronix TDS 520D - Page 9

Table of Contents
iv
TDS 500D, TDS 600C, TDS 700D & TDS 714L Performance Verification and Specifications
List of Tables
Table 1–1: Test equipment 1–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–2: DC offset accuracy (zero setting) 1–36. . . . . . . . . . . . . . . . . . . .
Table 1–3: DC Voltage measurement accuracy 1–40. . . . . . . . . . . . . . . . . .
Table 1–4: Analog bandwidth 1–45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–5: Delay between channels worksheet 1–52. . . . . . . . . . . . . . . . . .
Table 1–6: Delta time measurement 1–58. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–7: Available filters 1–97. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–8: Reference receiver filter options 1–97. . . . . . . . . . . . . . . . . . . . .
Table 1–9: Option 3C and 4C specifications 1–98. . . . . . . . . . . . . . . . . . . .
Table 1–10: Available receivers 1–98. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–11: Bessel Thompson frequency response and reference receiver
limits 1–106. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–1: Key features of TDS 500D, 600C, 700D and 714L
oscilloscopes 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–2: Record length and divisions per record versus
TDS model 2–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–3: Nominal traits — Signal acquisition system 2–11. . . . . . . . . . .
Table 2–4: Nominal traits — Time base system 2–12. . . . . . . . . . . . . . . . . .
Table 2–5: Nominal traits — Triggering system 2–13. . . . . . . . . . . . . . . . .
Table 2–6: Nominal traits — Display system 2–15. . . . . . . . . . . . . . . . . . . .
Table 2–7: Nominal traits — GPIB interface, output ports, and
power fuse 2–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–8: Nominal traits — Data handling and reliability 2–16. . . . . . . .
Table 2–9: Nominal traits — Mechanical 2–17. . . . . . . . . . . . . . . . . . . . . . .
Table 2–10: Warranted characteristics — Signal acquisition system 2–20
Table 2–11: Warranted characteristics — Time base system 2–22. . . . . . .
Table 2–12: Warranted characteristics — Triggering system 2–23. . . . . .
Table 2–13: Warranted characteristics — Output ports, probe
compensator, and power requirements 2–24. . . . . . . . . . . . . . . . . . . . .
Table 2–14: Warranted characteristics — Environmental 2–25. . . . . . . . .
Table 2–15: Certifications and compliances 2–27. . . . . . . . . . . . . . . . . . . . .
Table 2–16: Typical characteristics — Signal acquisition system 2–29. . .
Table 2–17: Typical characteristics — Time base system 2–32. . . . . . . . . .
Table 2–18: Typical characteristics — Triggering system 2–33. . . . . . . . .
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com