SAFE T Y IN FO R M A T IO N S H E E T
TRANSMITTER
GENERAL INFORMATION
Transmi tter T19
– T19-0 2 –
Abo u t T19 tran smi tters
Tele Radio AB's remote control systems are suitable for a wide variety of
applications for e.g. stationary or mobile equipments, hydraulic machines,
construction, forestry or agriculture equipments and more. Tele Radio AB's
transmitters and receivers are highly customizable and can be configured to
suit the most wide-ranging application requirements & usage habits.
T19 transmitters have simplex communication and work in either
discontinuous or continuous mode.
Abo u t thi s do cu ment
Every care has been taken in the preparation of this document. Please
inform Tele Radio AB of any inaccuracies or omissions. This document covers
general safety issues, main technical specifications, warranty, service and
maintenance and regulatory information. For more information, please refer
to the Enduser instructions and the Installation instructions available on
www.tele-radio.com. Images shown in this document are for illustrative
purposes only.
Warn in gs & restri ctio ns
Carefully read through the following safety instructions
before proceeding with the installation, configuration,
operation, or maintenance of the product. Failure to follow
these warnings could result in death or serious injury.
This product must not be operated without having read and understood the
Safety information sheet, the specific technical documentation (for
customized systems), and having received the appropriate training. The
purchaser of this product has been instructed how to handle the system
safely. The following information is intended for use as a complement to
applicable local regulations and standards.
IMPORTANT! Tele Radio AB remote controls are often built into wider
applications. These systems should be equipped with:
• a wired emergency stop where necessary
• a brake
• an audible or visual warning signal
INSTALLATION AND COMMISSIONING
IMPORTANT! Only licensed or qualified personnel should be permitted
to install the product.
This radio system must not be used in areas where there is
a risk of explosion.
Always switch off all electrical power from the equipment
before installation procedure.
To utilize the safety features of the system, use the stop
relays in the safety circuitry of the object/ equipment to be
controlled.
When the equipment controlled by the receiver's standard
relays is connected via the stop relays, make sure that the
maximum current through the stop relays is still within the
specifications. Contact your representative for assistance.
RISK OF UNINTENDED EQUIPMENT OPERATION
Only transmitters that are intended for use should be
registered in the receiver.
Failure to follow these instructions could result in death,
serious injury, or equipment damage.
RISK OF ELECTRIC SHOCK
The receiver must only be opened by qualified installers or
authorized personnel.
Make sure the power supply is switched off before opening
the receiver.
Failure to follow these instructions could result in death,
serious injury, or equipment damage.
OPERATION
Only qualified personnel should be permitted to access the
transmitter and operate the equipment.
l Make sure that the user satisfies the age requirements
in your country for operating the equipment.
l Make sure that the user is not under the influence of
drugs, alcohol and medications.
l Make sure that the user knows and follows operating and
maintenance instructions as well as all applicable safety
procedures and requirements.
The user should:
l Always test the transmitter stop button before
operating it.This test should be done on each shift,
without a load.
l Never use a transmitter if the stop button is
mechanically damaged.Contact your supervisor or
representative for service immediately.
l Never leave the transmitter unattended.
l Always switch the transmitter off when not in use. Store
in a safe place.
l Keep a clear view of the work area at all times.
MAINTENANCE
Before maintenance intervention on any remote controlled
equipments:
• always remove all electrical power from the equipment.
• always follow lockout procedures.
l Keep the safety information for future reference. Always download the
Safety information sheet from our website, www.tele-radio.com, for
the latest available version.
l If error messages are shown, it is very important to find out what
caused them. Contact your representative for help.
l The functionality of the stop button should be tested at least after
every 200 hours’ use.
l If the stop button is mechanically damaged, do not use the
transmitter. Contact your supervisor or representative for service
immediately.
SI-PN-TX103-EN-v02 1/4
To Next Page
Need help?
General
