Name: Teledyne T300
Brand: Teledyne
Rating: 5 (1 reviews)

To Next Page

Operation Manual

Model T300/T300M

Carbon Monoxide Analyzer

Also supports operation of:

Models T320 and T320U Analyzers

(when used in conjunction with T320/320U Addendum, PN07406)

9970 Carroll Canyon Road

SAN DIEGO, CA 92121-5201

USA

Toll-free Phone: 800-324-5190

Phone: +1 858-657-9800

Fax: +1 858-657-9816

Email: api-sales@teledyne.com

Website: http://www.teledyne-api.com/

Teledyne API 14 February 2012

Default Chapter5
- Operation5
- And Service7
- Operation9
- Operation10
- Corrected Safety Compliance (Was: IEC 61010-1:90 + A1:9211
- Table of Contents13
Part I General Information25
1 Introduction, Features and Options27
- T300 Family Overview27
- Features28
- T300/T300M Documentation28
- Options29
- Table 1-1: Analyzer Options29
- Operation30
2 Specifications and Approvals33
- Specifications33
- Table 2-1: T300/T300M Basic Unit Specifications33
- Table 2-2: O 2 Sensor Option Specifications34
- Table 2-3: CO 2 Sensor Option Specifications34
- Operation34
- EPA Equivalency Designation35
- Approvals and Certifications36
3 Getting Started37
- Unpacking the T300/T300M Analyzer37
  - Ventilation Clearance38
  - Table 3-1: Ventilation Clearance38
- Instrument Layout39
- Connections and Setup48
  - Electrical Connections48
  - Pneumatic Connections63
- Startup, Functional Checks, and Initial Calibration78
Part II Operating Instructions89
4 Overview of Operating Modes91
- Figure 4-1: Front Panel Display91
5 Setup Menu99
- SETUP à CFG: Configuration Information99
- SETUP à ACAL: Automatic Calibration100
- SETUP Àdas: Internal Data Acquisition System100
- SETUP à RNGE: Analog Output Reporting Range Configuration100
- SETUP à PASS: Password Protection111
- Table 5-2: Password Levels111
- SETUP à CLK: Setting the Internal Time-Of-Day Clock and Adjusting Speed113
  - Setting the Internal Clock's Time and Day113
  - Adjusting the Internal Clock's Speed113
- SETUP Àcomm: Communications Ports115
- SETUP Àvars: Variables Setup and Definition116
- Table 5-3: Variable Names (VARS)116
- SETUP Àdiag: Diagnostics Functions118
- SETUP Àmore à ALRM (Option): Using the Gas Concentration Alarms142
  - Table 5-10: CO Concentration Alarm Default Settings142
  - Setting the T300 Concentration Alarm Limits143
6 Communications Setup and Operation145
- Data Terminal/Communication Equipment (DTE DCE)145
- Communication Modes, Baud Rate and Port Testing145
- 147149
- Figure 6-3: COMM - COM1 Test Port149
- Ethernet150
- Table 6-2: Ethernet Status Indicators150
- RS-485 (Option)150
- USB Port (Option) for Remote Access155
- Operation156
- Communications Protocols157
7 Data Acquisition System (Das) and Apicom169
- Table 7-1: Front Panel LED Status Indicators for das169
- DAS Structure170
- Remote das Configuration188
8 Remote Operation191
- Computer Mode191
  - Remote Control Via APICOM191
- Interactive Mode192
  - Remote Control Via a Terminal Emulation Program192
- Remote Access by Modem194
  - Operation195
  - Operation196
- Password Security for Serial Remote Communications197
- Operation198
9 Calibration Procedures199
- Calibration Preparations199
  - Required Equipment, Supplies, and Expendables199
  - Data Recording Devices201
- Manual Calibration201
- Manual Calibration with Zero/Span Valves207
- Automatic Zero/Span Cal/Check (Autocal)214
- CO Calibration Quality220
- Table 9-5: Calibration Data Quality Evaluation220
- Calibration of the T300/T300M's Electronic Subsystems221
- Calibration of Optional Sensors225
  - O 2 Sensor Calibration225
  - CO Sensor Calibration Procedure229
10 Epa Calibration Protocol233
- Calibration Requirements233
- ZERO and SPAN Checks237
- Precisions Calibration239
  - Precision Calibration Procedures239
- Auditing Procedure239
- Dynamic Multipoint Calibration Procedure240
  - Linearity Test240
- References242
Part III Technical Information243
11 Maintenance Schedule & Procedures247
- Maintenance Schedule247
- Table 11-1: T300/T300M Maintenance Schedule249
- Table 11-2: T300/T300M Test Function Record250
- Predicting Failures Using the Test Functions251
- Maintenance Procedures252
12 Troubleshooting and Service255
- General Troubleshooting255
- Gas Flow Problems269
  - T300/T300M Internal Gas Flow Diagrams270
    - Figure 12-9: Internal Pneumatic Flow OPT 50H – Zero/Span Valves with Internal Zero Air Scrubber271
    - Figure 12-10: Internal Pneumatic Flow OPT 50E – Zero/Span/Shutoff W/ Internal Zero Air Scrubber272
  - Typical Sample Gas Flow Problems273
- Calibration Problems275
- Other Performance Problems277
  - Temperature Problems277
  - Excessive Noise279
- Subsystem Checkout280
- Repair Procedures291
- Frequently Asked Questions297
- Technical Assistance298
13 Theory of Operation299
- Measurement Method299
  - Beer's Law299
- Measurement Fundamentals300
  - Gas Filter Correlation301
- Flow Rate Control306
- Electronic Operation308
- Software Operation325
14 A Primer on Electro-Static Discharge327
- How Static Charges Are Created327
- How Electro-Static Charges Cause Damage328
- Common Myths about ESD Damage329
- Basic Principles of Static Control330
  - General Rules330
  - Basic Anti-ESD Procedures for Analyzer Repair and Maintenance331
Appendix A-1: Software Menu Trees, Revision L.8348
- Section 6348
Appendix A-2: Setup Variables for Serial I/O354
Appendix A-3: Warnings and Test Functions367
Appendix A-4: Signal I/O Definitions372
Appendix A-5: das Triggers and Parameters377
Appendix A-6: Terminal Command Designators380
Appendix A-7: Modbus Register Map381
- Operation392

Teledyne T300 User Manual

Table of Contents

Questions and Answers:

Teledyne T300 Specifications

Related product manuals

Brand	Teledyne
Model	T300
Category	Measuring Instruments
Language	English