Telephonics RDR-1600 - Page 80

Telephonics RDR-1600

81 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Default Chapter11
- Table of Contents11
Basic System Functions18
Chapter 1 . General Information18
Operational Modes19
Search Modes19
Weather Avoidance Modes19
Beacon Mode20
Dual Mode of Operation20
- Equipment Part Numbers and Descriptions20
RDR-1600 System Components20
CP-113 Unit Description22
CP-113 Function Select Switch22
CP-113 Mode Push Buttons23
- Additional Equipment Required for Complete Installation25
Additional Available Equipment25
Equipment Required but Not Supplied26
Leading Particulars27
RDR-1600 Radar System27
RT-1601 Receiver Transmitter29
DA-1203A Antenna Drive29
CP-113 Radar Control Panel33
Antennas33
DA-1203A Antenna Drive33
- Equipment Operation and Controls34
Operating Precautions34
License Requirements34
Figure 1.6-1. CP-113A Radar Control Panel35
Figure 1.6-2. CP-113K Radar Control Panel (with Brightness Pots)35
Operating Controls and Display Features35
CP-113 Operating Controls35
Figure 1.6-4. CP-113P Radar Control Panel36
Figure 1.6-5. Generic MFD Display (Radar Only Mode)39
MFD Display39
Operating Procedures39
General39
Turn on Procedure40
- Primary Mode Selection Procedures (WX, WXA, SR1, SR2, SR3, BCN)40
Range Selection Procedure41
Stabilization (STAB OFF) Control Procedure42
DO-172 Six-Pulse Beacon Interrogation45
- Target Alert Function48
Associated Publications48
Chapter 2 . Installiation49
- General49
- Installation Planning49
- Location of Equipment49
- Outline and Interconnect Drawings49
- Pre-Installation Check49
- Unpacking49
- Primary Power Requirements50
- Roll and Pitch Information50
- Assembly of Antenna Array and Antenna Drive Assembly Procedure51
- Installation of System Components51
- Radar Antenna51
- Post-Installation Check52
- Installation of CP-113 Radar Control Panel53
- Installation of RT-1601 Receiver Transmitter53
- Cabling54
- Installation of Waveguide and Cables54
- Waveguide54
- Post-Installation Check56
- Control Panel and MFD Display Check Procedure in Test Mode57
- Visual Inspection Procedure57
- Antenna Stabilization Check58
- Figure 2.7-2. Radar Control Panel60
- Antenna Checkout Aids61
- Pitch Calibration Check Procedure61
- Tilt Check Procedure61
- Roll Calibration Check Procedure62
- RF Operation Check Procedure63
- Interference Test Procedure64
- Preflight Check and Flight Check Procedures64
- Preflight Check Procedure64
- Single Indicators64
- Check Test Pattern67
- Flight Check Procedure67
- Multiple Displays67
- Check and Adjust Antenna Stabilization68
- Check Target Alert69
- Check Weather Alert Mode69
- Illustrations and Drawings70
- Testing Completed70
- Figure 2.9-1. Video Pattern, Level Flight71
- Figure 2.9-2. Video Pattern with Stab Error71
- Figure 2.9-4. Video Pattern, no Stabilization71
- Figure 2.9-5. RT-1601 Receiver Transmitter Outline Drawing74
- Figure 2.9-6. DA-1203A Antenna Drive Outline Drawing75
- Figure 2.9-7. CP-113 Radar Control Panel Outline Drawing76
- Figure 2.9-8. RDR-1600 System Wiring Diagram with Analog Gyros77
- Figure 2.9-9. RDR-1600 System Wiring Diagram with AHRS System78
- Figure 2.9-10. DA-1203A Antenna Mount Hole Pattern79

Other manuals for Telephonics RDR-1600

Pilot's Guide34 pages

Related product manuals

Telephonics RT-1601 RT

Telephonics CP-113K