- 1 -
Cod.954371
(EN) ................pag. 1
(IT) ..................pag. 4
(FR) ................pag. 7
(ES) ..............pag. 10
(DE) ..............pag. 13
(RU) ..............pag. 16
(PT) ...............pag. 19
(EL) ...............pag. 22
(NL) ..............pag. 25
(HU) ..............pag. 28
(RO) ..............pag. 31
(SV) ..............pag. 34
(DA) ..............pag. 37
(NO) ..............pag. 40
(FI) ................pag. 43
(CS) ..............pag. 46
(SK) ..............pag. 49
(SL) ...............pag. 52
(HR-SR) ........pag. 55
(LT) ...............pag. 58
(ET) ...............pag. 61
(LV) ...............pag. 64
(BG) ..............pag. 67
(PL) ...............pag. 70
MANUALE
ISTRUZIONE
(EN)
WELDER’S HELMET MANUAL
TELWIN S.p.A.
Via della Tecnica, 3 - 36030 VILLAVERLA (Vicenza) Italy
Informative note on the Model TW 6000 + TW 060 self-darkening lter, TW 6000 + TW 260 self-darkening lter.
Note: the terms helmet and lter are used in the text that follows.
The helmet model TW 6000 is in compliance with the EN 175 European Standard; the lters model TW 060 and TW 260
are in compliance with the EN 379 European Standard (Personal eye protection - Automatic welding lters) and with what is
prescribed by the 89/686/EEC Reference Standard.
TECHNICAL SPECIFICATIONS OF FILTERS TW 060, TW 260
- Overall dimensions: 110x90x9mm
- Visual area: 94x36.5mm (TW 060), 98x42mm (TW 260)
- Luminous state: gradation 4 DIN
- Dark state: variable gradation 4/5 - 9 and 4/9 - 13 DIN
- Protection from UV/IR : up to 13 DIN
- Sensitivity: adjustable
- Delay: adjustable
- Switching time: 0.4 ms
- Delay from dark state to luminous: 0.1 - 1 s with control knob
- Switch on / switch off: automatic
- Light sensors: 2 sensors (TW 060), 4 sensors (TW 260)
- Power supply: solar cell and replaceable lithium batteries (2xCR2032)
- Operating temperature: -5°C (+23°F)
+55°C (+131°F)
- Preservation temperature: -20°C (-4°F)
+65°C (+149°F)
- Structure: plastic
WARNING!
• Helmet users must read, learn and respect the basic rules given in this manual.
• The radiation emitted by the electric arc during welding can damage the eyes and burn the skin. In addition, welding
produces sparks and drops of molten metal that y in all directions. The protective helmet must be worn to avoid potentially
serious physical damages.
• Do not, for any reason, set re to the welding helmet because the smoke it produces will damage the eyes and body if
inhaled.
• The material used to make the whole helmet does not endanger people or the environment.
• Regularly check the conditions of the helmet:
- Before using it, make sure that the lter-glass is in the correct position and correctly xed in place: it must be exactly in
the space described.
- Keep the helmet away from ames.
- The helmet must not be placed too close to the welding area.
- When welding for extended periods, occasionally check the helmet to make sure there are no signs of deformation or
deterioration.
- Subjects with particularly sensitive skin must take extra care: materials that may come into contact with the skin can
cause allergic reactions.
• This self-darkening helmet is homologated only for protecting the face and eyes from ultraviolet and infrared radiation,
from sparks and welding sprays. It is not suitable for laser welding and oxy-acetylene welding or for protecting the face
against explosions or corrosive liquids.
• Only replace helmet parts with others that are specied in this manual. Non-observance of this regulation can expose the
operator to health risks.
• If the helmet does not darken or presents operation problems, refer to the TROUBLESHOOTING chapter; if the problem
persists immediately stop using the helmet and contact the person in charge or a distributor.
• Do not immerse the lter in water or other liquids; do not use solvents to clean the lter.
• Only use the helmet in temperatures of between: -5°C (+23°F) ÷ +55°C (+131°F).
• Only store the helmet in temperatures of between: -20°C (-4°F) ÷ +65°C (+149°F).
• Do not allow the lter to come into contact with liquid and dirt.
• Do not open the lter container.
• Never use the helmet without the internal and external transparent lter protections.
• Do not use replacement parts other than those original TELWIN.
Unauthorized modications and replacement parts will void the warranty and expose the operator to the risk of personal
To Next Page
Need help?
General