8-148-14
Note 1Note 1--Consult your lubricant supplier for the correct viscosity of lubricant to use when ambient temperatures areConsult your lubricant supplier for the correct viscosity of lubricant to use when ambient temperatures are
consistently above or below those listed.consistently above or below those listed.
Note 2 -Note 2 -Cummins Engine Co. do not recommend any specific brand of engine oil but the use of oils that meet API categories.Cummins Engine Co. do not recommend any specific brand of engine oil but the use of oils that meet API categories.
Cummins recommend use of only the multi-graded viscosity oils shown for the various ambient temperatures listed.Cummins recommend use of only the multi-graded viscosity oils shown for the various ambient temperatures listed.
Note 3 -Note 3 - Operation below the minimum temperatures listed for the oil used without proper preheat or warm-up results inOperation below the minimum temperatures listed for the oil used without proper preheat or warm-up results in
greatly reduced transmission life. If auxiliary heating is available, preheat the oil to the minimum temperature limit. If notgreatly reduced transmission life. If auxiliary heating is available, preheat the oil to the minimum temperature limit. If not
available, run the engine at part throttle with the transmission in neutral to raise the fluid temperature.available, run the engine at part throttle with the transmission in neutral to raise the fluid temperature.
Note 4 -Note 4 -
If rear axle has limited slip differential, an EP oil with limited slip additives should be used because using standardIf rear axle has limited slip differential, an EP oil with limited slip additives should be used because using standard
SAE 90 oil may result in very loud noise and jerking of the wheels when driving slowly round sharp corners.SAE 90 oil may result in very loud noise and jerking of the wheels when driving slowly round sharp corners.
Note 5 -Note 5 -Typical SAE 10W oils complying with Specification EMS19058 are:Typical SAE 10W oils complying with Specification EMS19058 are:
KKUUWWAAIIT T TTOO44 TTEEXXAACCO O TTEEXXTTRRAANN TTOOTTAAL L TTRRAANNSSMMIISSSSIIOON N AACC
SSHHEELLL L DDOONNAAX X TTCC MMOOBBIILLTTRRAANNS S HHDD BBP P AAUUTTRRAAN N 44
EESSSSO O TTOORRQQUUE E FFLLUUIIDD CCAASSTTRROOL L TTFFCC
Other lubricant suppliers may have comparable products and should be consulted for confirmation.Other lubricant suppliers may have comparable products and should be consulted for confirmation.
Temperature ConversionsTemperature Conversions
° ° CCeellssiiuuss --3322 --3300 --2277 --2255 --2200 --1188 --1155 --1100 00 1100 1155 2255 3322 3355 3388 4455 9933 119900
° ° FFaahhrreennhheeiitt --2266 --2222 --1177 --1133 --44 00 55 1144 3322 5500 5599 7777 9900 9955 110000 111133 220000 337755
RECOMMENDED LUBRICANTS (Continued)RECOMMENDED LUBRICANTS (Continued)
CCOOMMPPOONNEENNTT LLUUBBRRIICCAANNTT VVIISSCCOOSSIITTY Y ((SSeee e NNootte e 11))
RRiidde Ce Cyylliinnddeerrss HHyyddrraauulliic c ooiil l mmeeeettiinng g MMIILL--LL--22110044B B SSppeecciiffiiccaattiioonn.. SSAAE E 1100WW
(Nitrogen/Oil)(Nitrogen/Oil)
HHyyddrraauulliic Sc Sysystteemm HHyyddrraauulliic Tc Trraannssmmiissssiioon On Oiil ml meeeettiinng Sg Sppeecciiffiiccaattiioonn SSAAE E 1100WW
EEMMSS1199005588. . SSeee e NNootte e 55.. aat t aammbbiieennt t tteemmppeerraattuurrees s oof f --1188° ° tto o 3322° ° CC
SAE 30WSAE 30W
at ambient temps of 32° C and aboveat ambient temps of 32° C and above
To Next Page
Loading...
