Terumo BCT T5460 - User Manual

Questions and Answers

L
Lisa DouglasAug 17, 2025
Why doesn't the sealing start on my Terumo BCT T5460?
- M
  mcortezAug 17, 2025
  If the sealing process on your Terumo BCT Food Saver isn't initiating, several factors could be at play. First, check the electrodes for any moisture or dirt; if present, dry or clean them. Ensure the tube is dry as well. If you notice tiny arcs between the electrodes, drying them might resolve the issue. Also, verify that the trigger clicks fully when squeezed. A low or uncharged battery can also prevent sealing, so charge it for 3 hours. If the trigger does not “click" when it is fully squeezed, change Hand unit or contact your local Terumo BCT representative.
L
Laurie JohnsonAug 20, 2025
How to fix bad sealing on Terumo BCT Food Saver?
- J
  jacksonraymondAug 20, 2025
  A bad sealing on your Terumo BCT Food Saver may occur due to several reasons. Start by checking the battery charge level and charge if needed. Ensure the electrodes are clean and dry. If the moving electrode doesn’t move smoothly, you need to clean and oil electrode shaft. If the moving electrode is out of position, you need to check assembly of electrode. If the hand unit is defective change it or contact your local Terumo BCT representative.
M
Margaret JoyceAug 22, 2025
Why don’t the charge level LEDs light up on my Terumo BCT T5460 Food Saver?
- V
  Veronica PittsAug 23, 2025
  If the charge level LEDs on your Terumo BCT Food Saver aren't lighting up, it could be due to a few reasons. The battery voltage might be too low, in which case you should charge the battery for 3 hours. If that doesn't work, the fuse may be blown, or there could be another issue, and you should contact your local Terumo BCT representative.
B
Becky SpencerAug 26, 2025
What to do if charge level LEDs do not light up during charge of Terumo BCT T5460 Food Saver?
- J
  Jackie JacksonAug 26, 2025
  If the charge level LEDs on your Terumo BCT Food Saver do not illuminate during charging, the possible cause is no voltage. To solve this, charge the battery for 48 hours. If the LEDs still don't light up, the fuse may be blown, or there could be another issue, and you should contact your local Terumo BCT representative.
M
Marcia WallaceAug 28, 2025
Why is it hard to divide tube after seal with Terumo BCT T5460?
- M
  Michael AndersonAug 28, 2025
  If you're finding it hard to divide the tube after sealing with your Terumo BCT Food Saver, there might be a few reasons. Check if the electrodes are wet and dry them if necessary. Also, ensure the electrodes are clean. If the moving electrode doesn’t move smoothly in handle, you need to clean and oil electrode shaft. If the rim on moving electrode is damaged, contact your local Terumo BCT representative.
S
Sarah WalkerAug 31, 2025
What to do if charge level LEDs do not light up after 48 hours charge of Terumo BCT Food Saver?
- A
  April MontoyaAug 31, 2025
  If the charge level LEDs on your Terumo BCT Food Saver remain off even after a 48-hour charge, the battery unit might be defective. Consider changing the battery unit or contacting your local Terumo BCT representative for further assistance.
C
Courtney PattersonSep 3, 2025
Why is the sealing intermittent on my Terumo BCT T5460 Food Saver?
- L
  lynnrodriguezSep 3, 2025
  If you're experiencing intermittent sealing with your Terumo BCT Food Saver, it could be due to a defective hand unit, in which case you should change it or contact your local Terumo BCT representative. Alternatively, the cable might be broken, requiring you to contact your local Terumo BCT representative.
A
Alexander RomeroSep 5, 2025
Why is the hand unit LED still alight after seal trigger has been released on my Terumo BCT Food Saver?
- B
  Bryan TorresSep 5, 2025
  If the hand unit LED remains lit after releasing the seal trigger on your Terumo BCT Food Saver, it suggests a defective hand unit. Consider changing the hand unit or contacting your local Terumo BCT representative.
M
michaelmatthewsSep 8, 2025
Why does the hand unit LED flicker on my Terumo BCT Food Saver?
- H
  Heather HicksSep 8, 2025
  If the hand unit LED flickers on your Terumo BCT Food Saver, the cable might be broken. Contact your local Terumo BCT representative.
C
Chelsea WalkerSep 12, 2025
Why doesn’t the hand unit LED light up on my Terumo BCT T5460 Food Saver?
- P
  patricia31Sep 12, 2025
  If the hand unit LED doesn’t light up on your Terumo BCT Food Saver, it indicates a defective hand unit. Contact your local Terumo BCT representative.