Texecom Mirage Dual Technology - User Manual

1 PHYSICAL
4
9 COVERAGE AT 2m6 COVERAGE & PICK-UP 8 MOUNTING HEIGHT &
SETTINGS
1.5m
(4'10")
2.5m
(8'4")
3.1m
(10'0")
3.6m
(11'9")
4.1m
(13'6")
2.0m
(6'7")
-35°C (-31°F) to +60°C (+140°F)
190g (7oz) approx.
-10°C (14°F) to +55°C (+131°F)
66mm
(2.6”)
41mm
(1.6”)
116mm
(4.6”)
2.5mm (0.1”) ABS


✓
7 ANGLING THE DETECTOR
2 ENVIRONMENTAL
QUALITY ASSURANCE
WARRANTY
5 year replacement warranty.
The Mirage Dual Technology is designed to detect the movement of an
intruder and activate an alarm control panel. As the Mirage Dual Technology is not
a complete alarm system, but only a part thereof, Texecom cannot accept
responsibility or liability for any damages whatsoever based on a claim that the
Mirage Dual Technology failed to function correctly.
Due to our policy of continuous improvement Texecom reserves the right
to change specification without prior notice. All specifications are measured at
20˚C (68˚F).
Document Ref: M/EU/2.0-6
©1994 - 2004 Texecom Ltd
Certificate Number: FM 35285
3 FALSE ALARM PROTECTION
Design: Intelligent ADAPTIVE SIGNAL PROCESSING
™
(ASP
™
).
Noise reduction circuits with maximum ground plane.
Electrostatic Discharge: No false alarm up to 8kV air. Complies with
IEC 1000-4-2.
RF Immunity: No false alarm from 150kHz to 1GHz at 10V/m 100%
pulsed modulation. 30V/m 80% sinusoidal modulation.
Complies with IEC 1000-4-3. Equivalent to a 270W
uniform transmitter at 10ft (3m).
Fast Transient Immunity: No false alarm up to 4kV. Complies with IEC 1000-4-4.
RF Common Mode
Clamp: No false alarms 150kHz to 80MHz. Complies with
IEC 1000-4-6.
Conducted Emissions: Complies with IEC CISPR 22.
Radiated Emissions: Complies with IEC CISPR 22, FCC Part 15.
EMC: Independently certified to EN 50130-4 : 1996.
Microwave Range: Internal pot to adjust.
Approvals: Complies with: MPT 1349, I-ETS 300 440, FCC Part 15.
Pulse Count: Internal link to select.
INS 044-6
MIN
MIN
MAX
JP1
0.3 - 3.0m/s
A
B
C
D
E
FG
H
<24VDC 50mA (N/C)
<24V
DC
50mA, 18Ω (N/C)
9-16V
DC
20mA @ 12VDC
Latch Input Functions (see Section 5)
Remote LED: 12V 0V/NC
RL
LA
0V
12V
ALARM
TAMP
✗
MIN
MAX
MIN
MAX
MAX
JP1
✗
5 REMOTE LED & LATCH INPUT
FUNCTIONS
The latch terminal (see Section 4) can perform several different functions
depending on how it is connected:
Latch connected to Set Positive (SW+, Set+): The LEDs will be disabled while
the system is set. Any detectors triggered while the system is set will indicate
this by permanently lighting the Alarm LED (upon unsetting the system).
Detectors can be reset by taking the latch line high and then low again.
Latch connected to Alarm Positive (AL+, A+ve): The first detector activated
while the system is set will indicate this with a slowly flashing Alarm LED
(upon unsetting the system). Detectors which activated subsequently will
indicate this by permanently lighting the Alarm LED. Detectors can be
reset by taking the latch line high and then low again.
The latch input is not suitable for use on entry/exit or walk through zones.
Remote LED: Connect RL to12V to disable the walk test LEDs.
Connect RL to 0V or leave unconnected to enable the walk test LEDs.
MW ALARM PIR
➞
➞
PULSE COUNT
2
1
LED OFF
LED ON
IMPORTANT
Ensure Microwave Range is set at correct level for
desired coverage
MIN
MAX
JP1
1 - 10ft/s
Dual Technology Microwave & Infrared Detector
INSTALLATION INSTRUCTIONS
www.texe.com
THANK YOU FOR VOTING TEXECOM
Ask your distributor today for the new Texecom full colour Product Guide.
✓
✓
WINNER

Summary

Environmental Specifications

Operating Temperature Range 1

Operating temperature range from -35°C (-31°F) to +60°C (+140°F).

Operating Temperature Range 2

Alternate operating temperature range from -10°C (14°F) to +55°C (+131°F).

False Alarm Protection Features

Design and Signal Processing

Intelligent Adaptive Signal Processing (ASPTM) for noise reduction.

Electrostatic Discharge Immunity

Protection against electrostatic discharge up to 8kV.

RF Immunity Levels

Immunity to radio frequency interference up to 30V/m.

Fast Transient Immunity

Immunity to fast transient electrical bursts up to 4kV.

RF Common Mode Clamp Protection

Protection against RF common mode interference up to 80MHz.

EMC Compliance Standards

Compliance with EMC standards for emissions and immunity.

Pulse Count Sensitivity Setting

Adjustable sensitivity via pulse count setting.

Remote LED and Latch Input Functions

Latch Input: System Set Positive

Latch function for system set state, disabling LEDs.

Latch Input: Alarm Positive

Latch function for alarm state, indicating triggered detectors.

Remote LED Control

Configuration for the remote LED indicator behavior.

Mounting Height and Settings

Speed Detection Threshold

Setting for the speed detection threshold (0.3-3.0m/s or 1-10ft/s).

Coverage Diagram

Lens Assembly

Mounting the Mirage

Detector Knockouts and Installation

Texecom Mirage Dual Technology Specifications

General

Coverage Angle	90°
Technology	Microwave and PIR
Power Supply	9V - 16V DC
Alarm Relay	Normally Closed (NC)
Tamper Relay	Normally Closed (NC)