Texecom Prestige AMDT Plus - User Manual

1 INTRODUCTION
QUALITY ASSURANCE
WARRANTY
10 year replacement warranty.
The Prestige AMDT Plus is designed to detect the movement of an intruder and
activate an alarm control panel. As the Prestige AMDT Plus is not a complete
alarm system, but only a part thereof, Texecom cannot accept responsibility or
liability for any damages whatsoever based on a claim that the Prestige AMDT
Plus failed to function correctly.
Due to our policy of continuous improvement Texecom reserves the right to change
specification without prior notice. All specifications are measured at 20ºC (68ºF).
© 2006 Texecom Ltd. Document Ref: PAMDT+/EU/1.0
The Prestige AMDT Plus is protected by UK & International Registered Designs.
Registered Design No’s: 3004997, 3004260 & 3004261. Prestige is a Trademark of Texecom Ltd.
Certificate Number: FM 35285
INS 317-2
www.texe.com
Ask your distributor today for the Texecom full colour Product Guide.
3.0m/9’10”
2.5m/8’2”
2.0m/6’7”
1.5m/4’11”
8 MOUNTING HEIGHT & SETTINGS 7 TRIPLE END-OF-LINE (T-EOL)
The Prestige AMDT Plus is designed to be connected to a single zone on control
panels which feature Triple End-Of-Line (T-EOL) compatibility. Alarm, Tamper, Fault
and Masking are signalled on one pair of wires. To aid installation the resistor values
can be selected via the T-EOL plug-on board. All the connections are normally closed.
Masking is signalled by the alarm and fault relays opening simultaneously.
EOL ZONE
on control panel
TAMPER ALARM FAULT
T
A
F
PANEL
PIR
Selectable T-EOL Resistors
Use the Option A T-EOL board with Texecom’s Premier range of
control panels.
Grade 3 Anti-Masking Dual Technology
INSTALLATION INSTRUCTIONS
MADE IN
ENGLAND
For use with the following Premier software versions (or above)
Premier 24: V7 Premier 412/816: V10
Premier 48: V7 Premier 832: V3
Premier 88/168: V7 Keypads: V7
Premier 640: V7 Expanders: V7
A range of other T-EOL values are available separately.
2 CHOOSING A LOCATION
Avoid common false alarm sources
3 MOUNTING
For indoor use only
✓
✗
✓
✗
✓
Mount on a stable surface
5 WIRING
Do not run cable parallel to mains wiring
230V
110V
230V
110V
✓
✗
4 COVERAGE PATTERN
Volumetric
See Mounting Height Diagram (Section 8)
6 DETECTOR KNOCKOUTS
Rear tamper pull-out needs to be secured to
the mounting surface to meet Grade 3
requirements of TS50131-2-4
Rear tamper
pull-out
Fix both the detector
AND the rear tamper
pull-out to the wall.
DECLARATION OF CONFORMITY
1 2 3 4
ON
The Prestige AMDT Plus is a grade 3 anti-masking digital dual technology detector.
The combination of active IR and microwave proximity obstruction detection provides
unparalleled anti-masking reliability. Rear tamper protection, fault monitoring and Triple
End-Of-Line (T-EOL) signalling provide compliance with EN 50131-2-4.
Outstanding features include:
• 15m Volumetric PIR and Microwave Detection
• Active IR Anti-Masking
• Triple-End-Of-Line (T-EOL) Signalling
• Digital Microprocessor Technology
• Wall Tamper Detection
• Remote Self-Test Feature
1 2 3 4
ON
1 2 3 4
ON
This declaration is valid for the following product:
Device Type: Dual Technology Detector - DTD007-x
Product Name: Prestige DT/AMDT Plus
Equipment Classification: Short Range Device, Class 2
Notified Body Number: 0891
This is to confirm that this product meets all essential protection requirements relating to:
R&TTE Directive: 1999/05/EC
The assessment of this product has been based on the following standards:
EN 55022 : 1998 Emission Standard for Information Technology Equipment.
EN 50130-4 : 1996 Immunity Standard for Fire Intruder & Social Alarm Systems.
BS EN 60950-1 : 2002 Low Voltage Devices – Electrical Safety
ETSI EN 300 440-1 : 2001 Radio standard for short range devices (1GHz – 40GHz)
ETSI EN 301 489-3 : 2002 EMC standard for short range devices (9kHz – 40GHz)
On behalf of the manufacturer:
Texecom Ltd., 559 Wilbraham Road, Manchester, M21 0AE
This declaration is submitted by:
R J Austen, Managing Director
9th May 2006

Summary

Introduction to Prestige AMDT Plus

Choosing a Location for the Detector

Avoiding False Alarm Sources

Guidance on selecting a location to prevent false alarms from common sources.

Mounting the Detector

Mounting Surface and Tamper Security

Ensuring the detector is mounted securely on a stable surface and rear tamper is fixed.

Coverage Pattern Details

Wiring Recommendations

Cable Routing Guidelines

Advice on avoiding running detector cables parallel to mains wiring.

Triple End-Of-Line (T-EOL) Configuration

T-EOL Functionality and Compatibility

Details on T-EOL signaling, resistor selection, and control panel compatibility.

Altering Coverage and Detector Setup

Adjusting Coverage at 2 m Mounting Height

Instructions for modifying the detector's coverage pattern at a specific height.

Wiring and Detector Setup

Connecting the detector and configuring its basic settings.

Input Functions Configuration

Explanation of the detector's input functions and their operation.

Detector Features and Monitoring

Grade 3 Anti-Masking Functionality

Details on the detector's Grade 3 anti-masking capabilities and auto-optimization.

Fault Monitoring and Self-Test

How the detector monitors faults and performs local/remote self-tests.

LED Function Indicators

Description of the LED indications for different detector statuses.

Mounting Brackets and Physical Specifications

Ceiling and Wall Mount Brackets

Information on the provided ceiling and wall mounting brackets.

Physical Dimensions and Weight

Details on the detector's physical size, weight, and materials.

Standards, Approvals, and Environmental Conditions

Standards and Approvals Compliance

Listing of relevant standards and certifications the detector complies with.

Environmental Operating Conditions

Specifies the temperature and humidity ranges for detector operation.

Texecom Prestige AMDT Plus Specifications

General

Brand	Texecom
Model	Prestige AMDT Plus
Category	Security Sensors
Language	English