SERVICE KIT
SK 208-179B
4. Install th e TKS tank as follows:
A. (Refer to Figure 8) With 16 A N525-832R7 Screws and 16 NAS1149N832P Washers, install the tank
to the nut-plates that you installed on the belly of the airplane.
B. (Refer to Figure 14, View G-G and View H-H.) Install the 13146-05 LP Tank Wire Harness to the
TKS t ank .
C. Bon d and attach th e ground wires on the 13146-05 LP Tank Wire Harness to the lower inboard
mount screws on Auxiliary Pump 1 and Auxiliary Pump 2.
D. Atta ch the strap as s emblies around the tank and do not tight en at t his time.
E. (Refer to Fi gure 11, View E-E and View F-F.) Inside the airplane, tighten the 14 fasteners for the
forward and the aft TKS tank strap as s emblies.
F. On the straps assemblies under t he tank, torque the two self locking n uts t o 20 inch-pounds.
5. Install and connect the filler tubing and the v ent tubing as follows:
A. (Refer to Figure 20 , Detail A and View A-A.) P ut the S1053 K1 0W Du ct in po sition in the ai r plane
belly with the ZCT-TS-080 Tubing install ed on it at the two ends.
(1) Cut the ZCT -TS -080 Tubing down one side to make it fit on to the S1053K10W Duct .
NOTE: The inside d iameter of the ZCT - TS-080 is the same as the outside diameter of the
S1053K10W Duct .
(2) Attach th e ZCT-TS-080 Tu bing to the S105 3K 10W Du ct with S220 9-1 Ties.
B. Wrap P 840154 Tape around the part of the S1053K10W Duct that is adjacent to the filler port
where you will install the S1891-20S Clamp.
C. Atta ch the S 1053K10W Duct to t he filler port wi th the S1891-20S Clamp.
D. Do the routing of the S1053K10W Duc t toward the TKS tank.
E. (Refer t o Fig ure 20, View D-D, View G-G, and View H -H. ) W ith three S2209-1 Ties, attach the
S1053K10W Duc t to the structure at the three S2034-1 Mounts.
F. Use S2209-1 Ties to attach the S 1053K 10W Duct to the structure as neces s ary to make sure that
the duct doe s not t ouc h or cause inte rference with the structure or the cont rol cables.
G. (Refer to Figure 20, View B-B, View C-C, and View D-D.) Install three MS21919WDG22 Clamps
and three MS27039-1-08 Screws.
H. (Re fer to Figure 20, View E-E) Install one MS21919WDG26 Clamp and one MS27039-1-08 Screw.
I. (Refer to Figure 20, Detail A.) Wrap P 840154 Tape around the part of the S1053K10W Duct that is
adjacent t o the TKS tank where you will install the S1891-20S C lamp.
J. Attach the S 1053K10W Duct to t he TKS tank with the S1891-20S Clamp.
K. Attach t he S149 5-6 Hose to the filler port vent with the S2357-1 Clamp.
L. Do the routing of th e S 1495-6 H ose forward.
M. (Refer to Figure 19, D et ail A .) W ith the S3017-6-6-6 Tee an d three S2357-1 C lam ps , at tach the end
of the S1495-6 Hos e to t he two S 1495-6 H os es that attach to the tank .
N. With two S 2357-1 Clamps, attach the t wo S1495-6 Hoses to t he structure.
O. (Re fer t o F igure 19, View A -A, View B-B, View C-C, View D-D, View E-E , View F - F, View G-G, View
H-H, and View J-J.) With the four S2209-1 Ties , attach the S1495-6 Hoses to the structure at
the four S2034-1 M ounts.
6. (Refer to Figure 17, View B-B.) Install the bulkhead connectors on the airplane belly as follows:
A. In th e 0.87-i nc h diam eter hole that you m ade in the airplane belly, install the MN62 16 Bulkhead
Unequal Tee, two MN6211 Backnut s , and MN6782 5/16 Blanking Cap As se mbl y.
SK208-179B
February 7, 2013 Page 21
To Next Page
Loading...
