SERVICE KIT
SK 208-179B
(17) To make s ure t hat there is the same flow from one wing t o the o the r, m ak e s ure t hat you
collected 52 ounces +20 or −10 ounces, (1550 ml +600 m l or −300 ml) from eac h wing. T he
quantity of fluid collect ed from one side of the airpl ane sh ould be within 20 ounces (600 m l)
of th e qu ant ity collected from the ot her side o f the airplane.
(18) Put the FLUID C ONTROL PRIMARY switch t o the OF F position.
CAUTION: Do not operate the windshield pump for more than 10 sec onds c ontinuously and
there must be no less than 10 seconds between pump operations.
(19) Put the MAX FLOW switch to the WINDSHIELD position and release the sprin g-loaded switch.
(20) Make sure th at t he flu id flows ou t of t he winds hiel d spray collection tube.
NOTE: If the fl uid does not flow ou t of the winds hield spray collecti on tube, you c an move the
MAX FLO W switch to and from the WINDSHIELD position t hree or four times .
(21) Put the EX TERNAL POWER switch to the OFF position.
(22) Disconnect ex terna l power f rom t he airplane.
(23) Open the TK S fluid tank drain valve and let the tank drain completely.
(24) Close the T K S fluid t ank drain valve.
(25) Clean TK S fl uid and rem ov e collection equipment from the airplane as nece ssary.
(26) Remove the fluid collector system (plastic g uttering) below the pane ls.
(27) Remove the fluid collector system (plastic g uttering) below the pane ls.
D. Do a test of t he windshield ice detect light, wing inspection l ights , and nav l ights as foll ows:
(1) Make sure that the WI N G ICE DET LIGHT (HC027) and the N AV LIGHT (HC036) circuit
breakers are enga ged.
(2) Connect external power and pu t the EXTERNAL PO WER switch in the B US position.
(3) Move the WING LIGHT (S1021) to the ON p os ition and make sure that y ou ca n see the light
from t he w ing inspect ion light on the le ading edge of the left wing.
(4) Move the WING LIGHT to OFF.
(5) Move the NAV (S1017) s w itc h lig ht to ON.
(6) Make sure t he na vigat ions lights on both wings and the tail come on .
(7) Make sure that you can see the light from the windshield ice detect l ight on the winds hield from
thetopoftheglareshield.
(8) Move the NAV light switch to OFF.
(9) If one or m ore of t he lights do not operate correctly, troubleshoot the wiring in accordance with
Figure 16 and the w iring diagram ma nual. (Refer to the 208 Wiring Diagram M anual.)
31. Install all of the equipment and upholstery that you removed for access. (Re fer to t he Model 208
Maintenance Manual.)
A. (Refer to Fi gure 9, View A-A.) I ns t all the 2613498-2 Aft Fairing Assem bly as follo ws :
(1) Install the 2613498-2 Aft Fairing Assembl y with the 33 AN525-10R10 S crews and four
AN525-10R12 Screws.
(2) With U470644 Sealant, fillet s eal all around t he fl ange edge of the 2613498-2 A ft Fai r ing
Assembly where it is adj ac ent to t he f us elage.
B. Install t he radar and the radome. (Refer to the 208 Maintenance Manual, Chapter 34, Garmin
GWX-68 Weather Radar - Maintenanc e Practices.)
SK208-179B
February 7, 2013 Page 47
To Next Page
Loading...
