OWNER’S MANUAL
Technical Specifications
TL-2093 TL2095 TL-2094 TL-2091 TL-2092 TL-2096
Number of channels 2 channels 2 channels 4 channels 4 channels 4 channels 5 channels
Max Output Power (14.4v)
1000 Watts
Max
2000 Watts
Max
1500 Watts
Max
2000 Watts
Max
3000 Watts
Max
3000 Watts
Max
RMS Output Power (14.4v)
@ 4 ohm per channel
2 x 75 Watts
RMS
2 x 175
Watts RMS
4 x 75 Watts
RMS
4 x 100
Watts RMS
4 x 160
Watts RMS
4 x 100 and
1 x 375
Watts RMS
RMS Output Power (14.4v)
@ 2 ohm per channel
2 x 120
Watts RMS
2 x 275
Watts RMS
4 x 120
Watts RMS
4 x 140
Watts RMS
4 x 210
Watts RMS
4 x 140 and
1 x 570
Watts RMS
RMS Output Power (14.4v)
@ 4 ohm (bridge)
1 x 240
Watts RMS
1 x 500
Watts RMS
2 x 240
Watts RMS
2 x 250
Watts RMS
2 x 450
Watts RMS
2 x 285 and
1 x 375
Watts RMS
RMS Output @ THD+N < 1%:
@ 4 ohm per channel
@ 2 ohm per channel
@ 4 ohm bridge
Sub channel @ 4 ohm
Sub channel @ 2 ohm
2 x 60W
2 x 95W
1 x 190W
n/a
n/a
2 x 165W
2 x 235W
1 x 450W
n/a
n/a
4 x 60W
4 x 95W
2 x 190W
n/a
n/a
4 x 85W
4 x 120W
2 x 225W
n/a
n/a
4 x 135W
4 x 170W
2 x 330W
n/a
n/a
4 x 85W
4 x 125W
2 x 250W
1 x 280W
1 x 440W
Frequency Response
10 Hz – 25 kHz 10 Hz – 25
kHz (on 4x
channels)
10 ~ 180 Hz
(on Sub
channel)
Low Pass/High Pass Filter slopes
40 dB/oct
Low Pass Filter Range
50 ~ 750 Hz n/a on 4x
channels
40 ~ 180 Hz
on Sub
channel
High Pass Filter Range
50 ~ 500 Hz 20 ~ 200 Hz
on 4x
channels
10 ~ 50 Hz
on Sub
channel
(Subsonic)
Audio Input Level Sensitivity
0.2 ~ 5V
TDH @ 4 ohm load
(30% Rated Power)
< 0.02% < 0.02% < 0.02% < 0.02% < 0.02% < 0.033% on
4x channels
< 0.075% on
Sub channel
Signal/Noise Ratio
>90 dB >70 dB
Channel Separation
>89 dB
Minimum load (speaker) impedance
per channel
2 ohm 2 ohm on all
channels
Minimum load (speaker) impedance
(bridge)
4 ohm 4 ohm on 4x
channels
2 ohm on
Sub channel
Overheat protection temperature
80°C
Power Supply
DC 12V-14.4V
RCA Audio output
Yes – built
in, next to
RCA audio
input.
Yes – built
in, next to
RCA audio
input.
No – But RCA
“Y” splitter
cables are
provided.
No – But RCA
“Y” splitter
cables are
provided.
No – But RCA
“Y” splitter
cables are
provided.
No – But RCA
“Y” splitter
cables are
provided.
External fuse
30A 40A 40A (must
be installed
in power
cable - not
included)
60A (must
be installed
in power
cable - not
included)
80A (must
be installed
in power
cable - not
included)
80A (must be
installed in
power cable -
not included)
Accessories included
4x mounting
screws
4x mounting
screws
4x mounting
screws
2x “Y” RCA
splitter leads
and blocks
4x mounting
screws
2x “Y” RCA
splitter leads
and blocks
4x mounting
screws
2x “Y” RCA
splitter leads
and blocks
4x mounting
screws
2x “Y” RCA
splitter leads
and blocks
Remote bass controller
No Yes
(included)
Minimum specification of
Power and earth cable
8 AWG 4 AWG
Recommended amplifier wiring kit
TL-1192
2000 Watts
TL-1191
3000 Watts
Dimensions
(length x width x height)
186 x 195 x
60 mm
239 x 195 x
60 mm
239 x 195 x
60 mm
282 x 195 x
60 mm
347 x 195 x
60 mm
385 x 195 x
60 mm
All specifications are subject to change due to continued improvement and developments.
All content © Copyright TheLoudest.com 2009
OWNER’S
MANUAL
HIGH PERFORMANCE
MOSFET CLASS AB
CAR AMPLIFIER
TL-2093 - 2-Channel - 1,000 Watts Max - Up to 240 Watts RMS
TL-2095 - 2-Channel - 2,000 Watts Max - Up to 500 Watts RMS
TL-2094 - 4-Channel - 1,500 Watts Max - Up to 480 Watts RMS
TL-2091 - 4-Channel - 2,000 Watts Max - Up to 560 Watts RMS
TL-2092 - 4-Channel - 3,000 Watts Max - Up to 900 Watts RMS
TL-2096 - 5-Channel - 3,000 Watts Max - Up to 1,130 Watts RMS
SAFETY GUIDELINES | TECHNICAL SPECIFICATIONS
FEATURES | INSTALLATION AND OPERATION INSTRUCTIONS
To Next Page
Need help?
General
