What to do if my THOR HRD3088U Ranges oven is not coming on?
If your THOR Ranges oven isn't turning on, first, check if the power is on. If not, there might be an issue with the power supply. Also, verify that the range supply is switched on at the circuit breaker.
Why my THOR HRD3088U oven doesn’t work (no heating)?
If your THOR Ranges oven isn’t heating up (and the oven light and halos aren't on), check if the circuit breaker has tripped or if there's a power outage in your area. If it is a gas oven, contact your local gas supplier to check the gas supply.
Why are the burner flames very large and yellow on my THOR HRD3088U?
If the burner flames on your THOR Ranges are very large and yellow, try the following: Clean the burner bezel ring ports with a straightened paper clip, needle, or wire. Also, remove and carefully reinstall the burner bezel and caps. Make sure the type of cooktop matches the natural gas supply. Check the installation, replace the regulator, or set the regulator for the proper gas.
How to fix burners that won't light or don't burn evenly on THOR Ranges?
If some burners on your THOR Ranges won't light or the flames don't burn all around the burner cap, make sure the burner parts are clean, dry, and correctly assembled. Also, check that the igniters are clean and dry. Refer to the “Cleaning Instructions” for guidance.
How to prevent foods from being over-cooked or under-cooked in THOR HRD3088U?
If your food is consistently overcooked or undercooked in your THOR Ranges oven, adjust the cooking time, temperature, or rack position to achieve better results.
What to do if my THOR HRD3088U is sparking but there is no flame?
If your THOR Ranges is sparking but there's no flame ignition, make sure the gas shut-off valve is in the ON position.
Why does the burner flame go out at low setting on my THOR HRD3088U Ranges?
If the burner flame on your THOR Ranges goes out at the low setting, contact your gas company to check the gas supply pressure. Also, make sure that the air intake holes around the knobs are free from obstructions.
Why do the igniters spark continuously after flame ignition on my THOR HRD3088U Ranges?
If the igniters on your THOR Ranges spark continuously after the flame has ignited, have the power supply polarity corrected. Also, try drying or cleaning the igniters.
What to do if the flames have suddenly gone out on my THOR Ranges?
If the flames on your THOR Ranges have suddenly gone out, no action is required. The burner will detect this and automatically relight. However, if there has been a large spill, it's recommended to turn the burners off and clean the burners and sump area after the stove has cooled. Refer to “Cleaning Instructions”.
Why THOR HRD3088U Ranges oven will not heat?
If the oven on your THOR Ranges will not heat, make sure that oven settings are correct by following mode selection and clock settings as specified in the Oven Operation section of the manual.
Defines various safety symbols used throughout the manual to indicate potential hazards and important information.
Details the risks of electrical shock from the appliance and proper grounding procedures.
Explains the danger of the range tipping over and the importance of installing anti-tip devices.
Outlines precautions to prevent explosion hazards, particularly related to gas leaks.
Provides guidelines to prevent fire hazards, including keeping the area clear and proper cleaning.
Warns about potential poisoning hazards, such as carbon monoxide from blocked vents.
Details the risks of burns from hot surfaces during and after appliance use.
Offers additional general safety advice for operating and maintaining the appliance.
Provides specific measurements and clearance details for various installation scenarios.
Critical safety guidelines specifically for those installing the appliance.
Details on the required power supply cord kit and electrical requirements for the range.
Step-by-step guide for making the four-conductor wire connection to the range.
Specifies the electrical grounding and polarity requirements for safe operation.
Detailed steps for connecting the range to the gas supply line safely.
Safety recommendations for using various oven modes and preventing food contamination.
Details the warranty period for parts and labor, and conditions for coverage.
Outlines what services and repairs are covered by the manufacturer's warranty.
Lists exclusions from the warranty coverage, such as misuse or cosmetic damage.
To Next Page
General
