To Next PageTo Next PageWhat to do if my Titan Logix Corp Measuring Instruments unit displays Pout Er1?
If your Titan Logix Corp Measuring Instruments unit displays the message 'Pout Er1', it indicates that the K Factored Pulse Output has exceeded 60Hz. Press any key to return to normal operation. If the problem persists, consider setting the Pulse Output Multiplier to a higher value.
Why is my PLC or RTU not processing output pulses from the Flo Pro 9100 on my Titan Logix Corp Measuring Instruments?
If your PLC or RTU isn't processing output pulses from the Flo Pro 9100 in your Titan Logix Corp Measuring Instruments, first, ensure the Pulse output is wired correctly. If the issue continues, the pulses may be at too high a frequency for the RTU or PLC. In this case, try setting the Prescale jumper to a different setting.
What does CFg Err message mean on Titan Logix Corp Measuring Instruments?
If your Titan Logix Corp Measuring Instruments unit shows a 'CFg Err' message, there may be an error in the 10 Point Linearization setup. Ensure that all linearization parameters are set properly.
What does CFg Err2 mean on Titan Logix Corp Flo Pro 9100 Measuring Instruments after setting up for 10 point linearization?
If your Titan Logix Corp Measuring Instruments unit displays 'CFg Err2' after setting up for 10 point linearization, ensure the linearization frequencies are programmed in ascending order. Also, ensure that the differences between K factors do not exceed specified values.
What to do if my Titan Logix Corp Flo Pro 9100 unit does not power up with the battery pack?
If your Titan Logix Corp Measuring Instruments unit does not power up correctly when the battery pack is connected, first, unplug the battery pack, wait ten seconds, and then try again. If the problem persists, the battery pack may be discharged, so try a new battery pack.
Why is my Titan Logix Corp Flo Pro 9100 unit not registering accumulated totals or flow rates?
If your Titan Logix Corp Measuring Instruments unit does not register any Accumulated Totals or Flow Rates, ensure the magnetic pickup cable is properly connected and not broken. Also, check for a faulty magnetic pickup, or the flow meter itself may be faulty.
How to fix incorrect flow rate on Titan Logix Corp Flo Pro 9100 Measuring Instruments?
If you are experiencing an incorrect flow rate or accumulated total with your Titan Logix Corp Measuring Instruments, ensure the correct K Factor is programmed. Also, ensure the flow meter is installed correctly, the pulse output is connected properly, and that you are using the correct flow meter for the application.
What to do if there is incorrect accumulated total when using 0.1, 0.01, or 0.001 decimal point positions on Titan Logix Corp Flo Pro 9100?
If you observe an incorrect accumulated total when using 0.1, 0.01, or 0.001 decimal point positions on your Titan Logix Corp Measuring Instruments, ensure the K Factor programmed into the unit is equal to 1 unit of flow.
Details the manufacturer's warranty period, coverage, and limitations for the equipment.
Crucial safety warning regarding battery pack usage in hazardous environments.
Explains the purpose, scope, and intended audience of the instruction manual.
Provides a general description of the Flo Pro 9100 flow totalizer and rate meter.
Highlights the main functionalities and capabilities of the Flo Pro 9100 unit.
Guidelines for selecting an appropriate mounting location based on environmental factors.
Details the physical dimensions, layout of terminals, and jumpers on the unit.
Instructions for physically connecting the Flo Pro 9100 to a turbine meter.
Configuration of magnetic pickup sensitivity for optimal performance.
Setup and wiring for the optional pulse output signal to monitoring equipment.
Information on battery types, expected life, low battery indicators, and replacement.
Explanation of the various readouts and indicators on the Flo Pro 9100 display.
Steps for powering on the unit for the first time and initial setup.
Details on Active Mode and Power Save Mode functionalities.
How to navigate the display to view total flow and current rate.
Procedure for resetting the accumulated total count using the keypad.
Guide to setting crucial parameters like K Factor, linearization, and rate updates.
A table listing common problems and their corresponding solutions for quick diagnosis.
Lists detailed technical data, operating conditions, and certifications for the unit.
General| Category | Measuring Instruments |
|---|---|
| Manufacturer | Titan Logix Corp |
| Product Name | Flo Pro 9100 |
| Output Signal | 4-20 mA |
| Housing Material | Stainless Steel |
| Process Connection | 1.5" NPT |
