What causes unusual noise in my Titan 1507?
Unusual noise in your Titan Cutter can be caused by loose blade bolts or worn bushings, so tighten the bolts and check the bushings for wear, replacing them as needed. Bent blade carrier or blades can also cause unusual noises, so replace the blade carrier. Additionally, a bent deck causing the blades to contact it can be the source, so straighten the deck.
Why is grass cut lower in the center than the edge with my Titan Cutter?
If the grass is cut lower in the center of the swath than at the edge with your Titan Cutter, it's likely because the height of the rotary cutter is lower at the rear or front. Adjust the rotary cutter height and attitude so that the rear and front are within 1/2" of the same height.
Why won't the driveline telescope on my Titan 1507 Cutter?
If the driveline on your Titan Cutter won't telescope, it could be due to improper lubrication, so grease the driveline. A twisted driveline can also prevent telescoping, requiring you to replace it. Ensure the operator does not strike the ground with the blades. A bent driveline, often caused by being too long, should be replaced and shortened to the proper length. Damaged shields should also be replaced.
Why is the driveline twisted on my Titan 1507?
The driveline on your Titan Cutter might be twisted because it was overtorqued; avoid allowing the blades to contact the ground. Also, failing to maintain the correct PTO speed can cause this, so maintain 540 RPM PTO speed.
Why is my Titan 1507 Cutter leaving uncut material?
If your Titan Cutter is leaving uncut material, it might be due to excessive ground speed, so reduce it. Also, ensure that the RPM is not too low; maintain 540 RPM PTO speed.
What to do if the Titan 1507 material discharges unevenly?
If your Titan Cutter discharges material unevenly, creating bunches along the swath, it could be due to several factors. If the material is too high or there's too much of it, reduce ground speed while maintaining 540 RPM at the tractor PTO, or make two passes over the material, raising the rotary cutter for the first pass and lowering it to the desired height for the second, cutting at 90° to the first pass. Also, ensure the rear of the rotary cutter is high enough to allow material discharge, but not so high as to cause other issues. Wet grass can also cause this issue, so allow the grass to dry before mowing and slow the tractor's ground speed while keeping the engine at full PTO RPM. Lastly, the rear of the rotary cutter might be too low, trapping material underneath; adjust the rotary...
Warns against operating the rotary cutter without all safety shields properly installed to prevent injury.
Highlights safety as a primary concern in design and operation, emphasizing user alertness and training.
Explains safety alert symbols (DANGER, WARNING, CAUTION, NOTICE) and their meanings for hazard identification.
Mandates thorough training for all users and annual reviews. Untrained operators are not qualified.
Details the importance of familiarizing oneself with safety signs and their locations on the equipment.
Details steps for preparing and connecting driveline parts, including securing them.
Emphasizes the owner's responsibility for training users and ensuring they understand safety and operation.
Details tractor requirements for power, weight distribution, ROPS, and safety devices for safe operation.
Mandates the use of ROPS and seat belts on tractors to prevent rollover hazards and operator ejection.
Provides a chart matching rotary cutter models with recommended tractor horsepower and lifting capacity.
Provides instructions for safely disconnecting the rotary cutter from the tractor after operation.
Explains how to set cutting height and deck pitch for optimal cut quality, fuel efficiency, and even distribution.
Lists critical checks to perform before each operation to ensure the rotary cutter is safe and ready for use.
Guides operators through detailed safety and operating procedures for using the machine effectively.
Provides critical safety instructions for transporting the rotary cutter on public roads, including speed and visibility.
Covers procedures for inspecting, removing, and installing cutter blades, including sharpening tips.
Explains how to adjust the slip clutch to provide correct torque for tractor and gearbox protection.
Lists common cutting problems like uneven cuts and windrowing, their causes, and recommended solutions.
Details the limited warranty terms, coverage periods, exclusions, and purchaser's exclusive remedy.
To Next Page
General
