TKH SiQURA PD1022v2 - User Manual

© TKH Security B.V.
PD1022v2
2MP Network PTZ Dome Camera
Quick Start Guide
Unpack Installation Notices Connectors
SD Card & Default Default Button Camera Cabling
Find additional manuals, the
datasheet, the EU Declaration of
Conformity, and the latest firmware
for this product at:
tkhsecurity.com
Caution installation shall be performed by qualified
personnel only. Installation shall be in accordance with
local procedures. The camera contains batteries.
Battery replacement shall not be applied in view of the
risk of explosion. Dispose of used batteries according to
the instructions.
For "PoE" input connection, use only with UL listed
I.T.E. with "PoE" output. Description for the "PoE" is
intended to be connected to not exposed (outside plant)
networks or equivalent statement in installation
instructions.
Subject to modification. Actual product and accessories may differ in appearance.
Figure 1 Camera Connectors
2023 | Version 2 (20230209) | PD1022v2-QS-EN
RJ-45 Port
802.3at PoE+
Alarm in
Alarm Out
Audio I/O
Power (DC12V)
Ground
14-pin Alarm/Audio
I/O terminal block
Quick Start Guide
Camera Unit
Security Torx
Screws(4x) &
Plastic Screw
Anchors (4x)
Gland Sets
Combi-connector 3-
pin(2x), 4-pin(1x)
Silicone Plug
Decorative Rim
Memory Card Slot
Memory Card Cover
Remove the silicon plug and
unscrew 4x to remove cover
Remove memory card cover
and insert Micro
SD/SDHC/SDXC up to
128GB
Table 1 Connector definition
No. Connector Definition
1 Alarm I/O Alarm I/O connection
2 Audio I/O Line In and Line Out connection
3
RJ-45 Port
(Contact Siqura for
a compatible PoE
injecter.)
For network and PoE connections
4 Power(DC 12V) Power Connection
5 Reset Button
To restore camera to factory defaults, power
up with Reset button pressed for at least 10s.
6 Micro SD Card Slot
Insert the SD card into the card slot to store
videos and snapshots. Do not remove the SD
card when the camera is powered on.
1
2
3
4
5
Figure 3 – Position of default button
Press the button with a proper
tool for at least 20 seconds to
restore the system.

Summary

Unpack and Components

Package Contents

Lists all included accessories such as gland sets, connectors, screws, and terminal blocks.

Installation Notices

Camera Connectors

Alarm I;O Connection

Interface for alarm input and output signals.

Audio I;O Connection

Interface for line-in and line-out audio signals.

RJ-45 Port for Network and PoE

Port for network connectivity and Power over Ethernet (PoE).

DC 12 V Power Connection

Connection point for the 12V DC power adapter.

Reset Button

Button to restore camera to factory defaults.

Micro SD Card Slot

Slot for inserting a micro SD card for video and snapshot storage.

SD Card and Default Settings

SD Card Installation

Instructions for inserting a micro SD card for storage.

Default Button Operation

Procedure to restore the system to factory defaults using the button.

Accessing the Camera

DHCP Network Access

Method for accessing the camera via DHCP for initial connection.

Fixed IP Network Access

Method for accessing the camera using a fixed IP address.

Auto Detect with SDM2

First Time Camera Login

Setting a Strong Password

Guide to setting a secure password for the camera.

Login Procedure

Steps to log in to the camera interface.

Browser-based Viewer

TKH SiQURA PD1022v2 Specifications

General

Model	PD1022v2
Category	Security Camera
Type	Dome
Sensor Size	1/2.8"
Night Vision	Yes
Weather Resistance	IP66
Resolution	1920 x 1080
Lens	2.8mm
IR Distance	30m
Video Compression	H.264
Power Supply	PoE (802.3af)
Operating Temperature	-30°C to +60°C
Storage	MicroSD card