1
2
3
4
5
6
1
2
3
4
5
7
6
1
2
3
4
5
6
7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
adjusting the sound sensitivity
You can change the level of sensitivity on your baby monitor to suit your baby. For example, if your baby is a
particularly quiet sleeper, you can increase the sensitivity levels so that you are sure to hear if baby disturbs
or becomes uncomfortable.
There are 5 different levels. The microphone will be voice activated by the noise baby makes. Level 5 is the
most sensitive. The sound sensitivity settings of the baby unit can be changed only when parent unit is
linked with the baby unit:
Press <MENU> to access main menu
Press ▲ UP or ▼ DOWN to select SENSITIVITY.
Press <MENU> to enter the sub-menu.
Press ▲ UP or ▼ DOWN to select from Level 1 to Level 5.
Press <MENU> to confirm.
setting the temperature format
The Baby Unit constantly monitors the temperature in your baby’s room and alerts you if it gets too hot or too
cold. The temperature is displayed
Press <MENU> to access main menu
Press ▲ UP or ▼ DOWN to select TEMPERATURE.
Press <MENU> to select Format.
Press <MENU> to enter the sub-menu.
Press ▲ UP or ▼ DOWN to select Celsius or Fahrenheit.
Press <MENU> to confirm.
The real-time temperature format displayed on the status bar of parent unit will be changed accordingly.
setting the vibration
Press <MENU> to access main menu
Press ▲ UP or ▼ DOWN to select VIBRATION.
Press <MENU> to enter the sub-menu.
Press ▲ UP or ▼ DOWN to turn the vibration ON or OFF.
Press <MENU> to confirm.
If ON, the Parent Unit will vibrate once to confirm it is activated.
paging to locate the parent unit
If both ▲ UP (9a) and ▼ DOWN (9b) keys are pressed for 3 seconds on the baby unit at the same time,
the paging tone is emitted.
PAGING will be displayed on the LCD of the parent unit.
If volume is OFF before paging starts, reset it to default volume level (4).
During paging, any key pressed on the parent unit will stop the paging tone.
If the link is lost between the parent unit and the baby unit, the paging tone will not be emitted when
both ▲ UP (9a) and ▼ DOWN (9b) keys are pressed together. There will be no change on baby unit.
If paging is not stopped, it will expire in 2 minutes.
Paging function does not work if parent unit is turned off.
resetting to default settings
parent unit default
Ensure the parent unit is powered OFF.
Press and hold ▲ UP.
Press POWER.
The parent unit LCD will display ‘please press M to restore default settings’.
Press M to confirm.
NOTE:
• If LCD is off, and baby voice reaches the sensitivity level 3,4 or 5, the LCD will be turned on
automatically.
• When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds
and therefore transmits more often. As a result, the units will consume more power.
NOTE:
The temperature displayed is for reference only. There may be a slight tolerance of the degree
accuracy comparing with the actual temperature. It is important to physically check the actual
temperature in your baby’s room regularly.
NOTE:
• In vibration mode, the parent unit will vibrate when the noise level from the baby reaches
sensitivity level 3, 4 or 5 while the loudspeaker volume of the parent unit is switched o.
• If the Parent Unit speaker volume is turned off whilst in monitoring mode and vibration mode,
the Parent Unit will vibrate once.
• When the noise level from the baby reaches sensitivity level 3, 4 or 5, the vibrating alert is
triggered and will vibrate every 5 seconds.
baby unit default
Ensure the parent unit is powered OFF.
Press and hold ▲ UP.
Press POWER ON, whilst still holding ▲ UP.
After 3 seconds, the sensor pad alarm LED will flash.
Release ▲ UP key and press ▼ DOWN key. The sensor pad LED will resume on.
15
14
To Next Page
Loading...