Topcom Twintalker 9500 - 13.10.3 Scan for DCS Code; 13.11 Call Tones; 13.12 Roger Beep On;Off; 13.14 Dual Channel Monitor Function

8
Twintalker 9500
13.10.3 Scanning for a DCS code
Once there is a transmission on the channel, the DCS code (if used) will be detected and
displayed.
13.11 Call Tones
A call tone alerts others that you want to start talking.
13.11.1 Setting the Call Tone
The Twintalker 9500 has 15 call tones.
13.11.2 Sending a call Tone
Press the button briefly. The call tone will be transmitted on the set channel.
13.11.3 Call tone reception type
• Press the -button nine times.
• Press the -button or -button to select the call tone reception type.
1. Tone only
2. Tone + vibration
3. Vibration only
Press the -button to confirm and return to stand-by mode.
13.12 Roger Beep On/Off
After the -button is released, the unit will send out a roger beep to confirm that you have
stopped talking.
To set the Roger Beep.
• Press the - button ten times. ‘rO’ will be displayed.
• Press button to enable (ON) or button to disable the Roger-
Beep (OFF).
• Press the - button to confirm your selection and return to the
standby mode.
13.13 Key-Tone On/Off
When a button is pressed, the unit will beep briefly.
To set the key-tone.
• Press button eleven times. ‘tO’ will be displayed.
• Press button to enable (ON) or button to disable the Key
Tones (OFF).
• Press the - button to confirm your selection and return to the.
standby mode.
13.14 Dual Channel Monitor function
In stand-by, the PMR is set on one channel with CTCSS/DCS code. The PMR will only receive
signals transmitted on that channel with the CTCSS/DCS code.
Dual Channel Monitor (DCM) allows you to monitor a second channel with CTCSS/DCS code.
When the Dual Channel Monitor function is activated, the PMR will switch sequentially between
the standby channel + CTCSS/DCS code and the Dual Channel + CTCSS/DCS code.
• Press the -button seven times : "SCAN" and "DCS
00" flashes on the display for the selected radio channel.
• Press the -button or the -button to start the
DCS scan.
• Press the - button eight times, “C” is displayed and
the current call tone is flashing.
• Press the - button
or the - button to change to
another Call Tone.
• Press the - button to confirm and return to stand-by
mode.
• If you press the button while listening to a found CTCSS
code, the PMR will go back in stand-by mode on the channel with
the CTCSS code.
• If no CTCSS code is detected there is a chance that DCS is
selected by the user. In this case you can scan for the DCS code.
(section 13.10.3)
PTT
12
7
11
10
If you press the button while listening to a found DCS code, the
PMR will go back in stand-by mode on the channel with the DCS code.
PTT
12
7
11
10
PTT
12
6
7
11
10
PTT
12
• Press the -button twelve times,” DCM OFF" will
flash on the display.
• Press the -button or the -button to change the
channel.
• Press the -button to confirm the channel selection
and go to CTCSS selection. (Press the -button
again to go to DCS selection)
• Press the -button or the -button to change
the CTCSS code or DCS code.
• Press the -button to confirm and return to stand-by
mode.
• To disable the function select "OFF" when selecting the
DCM channel.
PTT
12
7
11
10
PTT
12
7
11
10
PTT
12
7
11
10
7
7
11
10
PTT
12