5
© 2009 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO181/211
TROUBLESHOOTING
5 - 47
08-1214_3 (Transfer charger wire (Present driving counts))
08-1214_4 (Transfer charger wire (Recommended driving counts to be replaced))
08-1214_6 (Transfer charger wire (Present output pages for control))
08-1214_7 (Transfer charger wire (Present driving counts for control))
08-1246_0 (Fuser roller (Present number of output pages))
08-1246_1 (Fuser roller (Recommended number of output pages for replacement))
08-1246_3 (Fuser roller (Present driving counts))
08-1246_4 (Fuser roller (Recommended driving counts to be replaced))
08-1246_6 (Fuser roller (Present output pages for control))
08-1246_7 Fuser roller (Present driving counts for control))
08-1250_0 (Pressure roller (Present number of output pages))
08-1250_1 (Pressure roller (Recommended number of output pages for replacement))
08-1250_3 (Pressure roller (Present driving counts))
08-1250_4 (Pressure roller (Recommended driving counts to be replaced))
08-1250_6 (Pressure roller (Present output pages for control))
08-1250_7 (Pressure roller (Present driving counts for control))
08-1268_0 (Fuser roller separation finger (Present number of output pages))
08-1268_1 (Fuser roller separation finger (Recommended number of output pages
for replacement))
08-1268_3 (Fuser roller separation finger (Present driving counts))
08-1268_4 (Fuser roller separation finger (Recommended driving counts to be replaced))
08-1268_6 (Fuser roller separation finger (Present output pages for control))
08-1268_7 (Fuser roller separation finger (Present driving counts for control))
08-1298_0 (Feed roller (Drawer) (Present number of output pages))
08-1298_1 (Feed roller (Drawer) (Recommended number of output pages for replacement))
08-1300_0 (Feed roller (PFU) (Present number of output pages))
08-1300_1 (Feed roller (PFU) (Recommended number of output pages for replacement))
08-1316_0 (Separation roller (Bypass unit) (Present number of output pages))
08-1316_1 (Separation roller (Bypass unit) (Recommended number of output pages
for replacement))
08-1324_0 (Feed roller (Bypass unit) (Present number of output pages))
08-1324_1 (Feed roller (Bypass unit) (Recommended number of output pages
for replacement))
08-1336_0 (Recovery blade (Present number of output pages))
08-1336_1 (Recovery blade (Recommended number of output pages for replacement))
08-1336_3 (Recovery blade (Present driving counts))
08-1336_4 (Recovery blade (Recommended driving counts to be replaced))
08-1336_6 (Recovery blade (Present output pages for control))
08-1336_7 (Recovery blade (Present driving counts for control))
08-1372 (Heater and energizing time accumulating counter Display/0 clearing)
08-1378 (Counter for period of time fuser unit is at ready temperature)
08-1380 (Counter for period of time fuser unit is at printing temperature)
08-1382 (Counter for period of time fuser unit is at energy saving temperature/
Counter reset)
08-1385 (Number of output pages (Thick paper 1))
08-1386 (Number of output pages (Thick paper 2))
08-1388 (Number of output pages (OHP film))
08-1410 (Counter for period of toner cartridge rotation time)
08-1411 (Counter for envelope)
Also, set the setting values which have been changed for servicing.
(17) Check that the setting value for 08-203 (Line adjustment mode) is "0" (For factory shipment). If it
is “1” (For line), change it to “0”.
To Next Page
Loading...
