To Next PageTo Next Page
Need help?Do you have a question about the Toshiba MMD-AP0181BH and is the answer not in the manual?
General| Brand | Toshiba |
|---|---|
| Model | MMD-AP0181BH |
| Category | Air Conditioner |
| Language | English |
Lists various indoor unit types including cassette, duct, wall, and floor standing models.
Diagram showing the outdoor unit and its components.
Lists models of Flow Selector Units used with the system.
General warnings and requirements for safe installation practices.
Warnings related to operating, moving, and repairing the air conditioner.
Additional cautions and specific checks for installation safety and proper setup.
Details and diagrams of various indoor unit parts like grilles, filters, and flaps.
Diagram of the outdoor unit, showing its inlets, outlets, and fixing legs.
Lists optional remote controller units available for purchase.
Explains the indicators and displays shown on the remote controller screen.
Describes the function of each button on the remote controller for operation.
Steps before using the air conditioner and operational requirements for initial use.
How to set louvers horizontally for optimal cooling effect.
Specific airflow adjustments for the 4-way cassette type in cooling and heating.
Procedures for adjusting air direction and the swing function using the remote.
Adjusting airflow and swing for the 2-way cassette type.
Adjusting airflow direction for the 1-way cassette type.
Adjusting airflow and swing for under ceiling and 1-way cassette types.
Adjusting airflow direction for the high wall type indoor unit.
Adjusting airflow direction for floor standing cabinet type units.
Adjusting airflow direction for floor standing type units.
Explains how to set different timer types (ON, OFF, Repeat OFF) and cancel them.
Guidelines for selecting an appropriate and safe site for unit installation.
Requirements and procedures for safe and correct electrical wiring.
Instructions for cleaning air filters and performing daily care.
Steps for cleaning air filters, grilles, and main units.
Advice on maintaining room temperature, cleaning filters, and airflow for efficiency.
Covers pre-operation checks, heating capacity, and defrost operation details.
Details on protection mechanisms, power failures, fan rotation, and operation characteristics.
Prohibited locations for installation to avoid issues like noise and malfunction.
Guidelines for minimizing noise and vibration during installation.
Lists common symptoms, their causes, and distinctions between normal operation and failures.
How to check the recorded error history using the remote controller.
Details of included and required accessory parts for installation.
Safety advice related to handling and installing accessory parts.
Explains warning and caution symbols used throughout the manual.
Guidelines for safe handling, loading, and transportation of outdoor units.
Requirements for foundation strength and protection against snowfall.
Specifics on mounting, vibration-proofing, and unit arrangement for multiple units.
Examples and dimensions for connecting refrigerant pipes between units.
Specifications for pipe materials and capacity codes for indoor/outdoor units.
Tables for selecting pipe sizes based on capacity and connection types.
Selection criteria for FS units and minimum pipe wall thickness for R410A.
Limits for pipe length and height differences between units for proper operation.
Steps for performing airtight tests and purging air from the system.
How to operate valves and perform gas leak checks using detectors.
How to calculate and charge additional refrigerant amounts.
Instructions for fully opening valves and insulating refrigerant pipes.
Comprehensive warnings for installation professionals regarding electrical and refrigerant safety.
Guidelines for power supply wiring, fuse selection, and connection requirements.
Wiring diagrams and specifications for combined outdoor units and wire sizing.
Details on control wiring between units, remote controllers, and FS units.
Details on control wiring and power supply for indoor units.
Overall wiring diagram showing connections between outdoor, FS, and indoor units.
How to connect power and control wires to the outdoor unit's terminal blocks.
Steps for automatically setting addresses for indoor units connected to the system.
Steps for manual address setup using switches on the PC board.
How to set indoor unit addresses using the wired remote controller.
How to check the assigned indoor unit addresses and their positions.
How to verify unit positions within a group control setup.
How to modify indoor unit addresses via the remote controller.
How to change all indoor addresses using a single remote controller.
Procedures to reset unit addresses to factory defaults.
Important considerations for connecting multiple indoor units to a single FS unit.
Procedure to set the item code for configuring FS units with multiple indoor units.
Steps to set a specific indoor unit for cooling-only mode.
Steps and precautions before and during test operations using the remote controller.
Performing test operations via the outdoor unit's PC board switches.
Guide to interpreting segment displays and troubleshooting codes for outdoor units.
Details of included and required accessory parts for the system.
Safety advice related to handling, installing, and using accessory parts.
Tools and precautions for installing systems with new refrigerant (R410A).
Material and dimension requirements for refrigerant piping with R410A.
Prohibited locations for installation to avoid issues like gas leaks and interference.
Specific dimensions and clearances required for unit installation and service.
Visual guide and safety requirements for flow selector unit installation.
Procedures for installing hanging bolts for the flow selector unit.
Steps for securely mounting the flow selector unit.
Specifications for pipe length, height differences, and material selection.
Diagrams showing how to connect refrigerant pipes to valves.
Procedures for flaring pipes and making refrigerant pipe connections.
Procedures for testing airtightness, purging air, and insulating pipes.
Safety and procedural requirements for electrical work.
Instructions for connecting wires to the flow selector unit.
Diagrams showing wiring between units and FS units.
Overall wiring diagram showing connections between outdoor, FS, and indoor units.
Specific wiring instructions for cassette type indoor units.
Wiring instructions for other indoor unit types like duct and wall mounted.
Wiring instructions for concealed duct standard and high static pressure types.
Wiring instructions for concealed slim duct and high static pressure duct types.
Wiring instructions for under ceiling and high wall type indoor units.
Wiring instructions for high wall and floor standing cabinet type indoor units.
Wiring instructions for floor standing concealed type indoor units.
Guidelines and limits for refrigerant concentration in rooms to prevent suffocation.
