To Next PageTo Next PageWhat does error H16 mean on a Toshiba MMY-MUP1401HT8P-E Air Conditioner?
If your Toshiba Air Conditioner displays error code H16, it indicates Oil level detector circuit trouble. It could be TK1 or TK2 oil circuit trouble.
Why does my Toshiba MMY-MUP1401HT8P-E Air Conditioner remote controller display a check code?
If your Toshiba Air Conditioner displays a check code on the remote controller, it might be due to duplicated addresses. Here's how to address it: 1. **Indoor Addresses:** Ensure that indoor unit addresses are not duplicated. If duplicates are found, reconfigure the address settings. 2. **Outdoor Addresses:** If you manually set up outdoor addresses, avoid doing so, as this can cause conflicts. 3. **Line Addresses:** If you connected U1/U2 and U3/U4 connectors, modify the line address setup of the header unit between lines by setting up SW13 and SW14 on the interface PC board.
What to do if a Toshiba Air Conditioner check code appears after installing an outdoor backup?
If your Toshiba Air Conditioner shows a check code, and you've recently installed an outdoor backup or noticed a decrease in connected outdoor units, here’s what to do: * **Outdoor Backup Installation:** If the error occurred during backup installation, clear the trouble code after the setup is complete. * **Follower Unit Power:** Ensure that the power to any follower units is turned on. If it's off, switch it on.
What if a check code on Toshiba Air Conditioner persists after troubleshooting steps?
If a check code is still appearing on your Toshiba Air Conditioner remote after trying other solutions, the issue might be with the interface PC board. In this case, the suggested solution is to replace the interface PC board.
What if a Toshiba MMY-MUP1401HT8P-E Air Conditioner check code is caused by address setup trouble?
If your Toshiba Air Conditioner is showing a check code, and the address setup is the cause, the suggested solution is to set up the addresses again. Modify the setup.
What does error E31 mean on a Toshiba Air Conditioner?
Error code E31 on your Toshiba Air Conditioner indicates an inverter communication trouble, or communication trouble between MCU and sub MCU.
What does error E19 mean on a Toshiba MMY-MUP1401HT8P-E Air Conditioner?
Error E19 on your Toshiba Air Conditioner indicates Number of header outdoor unit trouble.
Why does my Toshiba MMY-MUP1401HT8P-E Air Conditioner show error E06?
Error E06 on your Toshiba Air Conditioner can be due to a decrease in the number of indoor units. In a TU2C-LINK communication system, this error can also occur if the termination resistance is not set in any of the indoor units.
What does error H08 mean on a Toshiba Air Conditioner?
If your Toshiba Air Conditioner displays error code H08, it indicates temperature sensor trouble for oil level. It could be TK1 or TK2 sensor trouble.
What does error F09 mean on a Toshiba MMY-MUP1401HT8P-E?
If your Toshiba Air Conditioner displays error code F09, it indicates TG1, TG2 or TG3 sensor trouble.
General| Brand | Toshiba |
|---|---|
| Model | MMY-MUP1401HT8P-E |
| Category | Air Conditioner |
| Language | English |
Details protective gear for tasks and explains unit warning symbols (WARNING/CAUTION).
Safety measures for installing and operating the air conditioner.
Explains the icons and indicators shown on the remote controller display.
Instructions for operating the unit, selecting modes, and setting the OFF timer.
Steps for standby, starting, and running the air conditioner.
Guide to setting operation modes, fan speeds, and desired temperatures.
Guides users through checking common symptoms before service calls.
