Toshiba RAS-18 - Remote Control and Operation Modes; Remote Control Overview; Core Operation Modes

Preparing Filters
1. Open the air inlet grille and remove the air filters.
2. Attach the filters.
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is flashing, go to the next step 2.
2. Press
or : adjust the time.
3. Press
: Set the time.
Remote Control Reset
Push
by tip of the pencil or
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
INDOOR UNIT DISPLAY
1
PREPARATION BEFORE USE
2
AIR FLOW DIRECTION
3
Note:
●
The provided Remote Controller is a wireless type, which also can be
used as a wire. Please see “How to Connect The Remote Controller
for Wired Operation”, located in installation instruction, in case of wired
control is required.
●
In wire operation, remote controller will return to initial condition
(PRESET, TIMER and CLOCK will return to initial condition) when user
shutdown power supply of Air conditioner.
REMOTE CONTROL
4
AUTOMATIC OPERATION
6
To automatically select cooling, heating, or fan only operation
1. Press
02'(
: Select Auto A.
2. Press
: Set the desired temperature. Min. 17°C, Max. 30°C.
3. Press
)$1
: Select AUTO, LOW , LOW+ , MED ,
MED+
, HIGH or Quiet
1. Press
02'(
: Select Cool , Heat , or Fan only .
2. Press
: Set the desired temperature. Min. 17°C, Max. 30°C.
Fan Only: No temperature indication
3. Press
)$1
: Select AUTO, LOW , LOW+ , MED ,
MED+
, HIGH or Quiet
COOLING / HEATING / FAN ONLY
OPERATION
5
DRY OPERATION
7
For dehumidification, a moderate cooling performance is controlled
automatically.
1. Press
02'(
: Select Dry .
2. Press : Set the desired temperature. Min. 17°C, Max. 30°C.
Note: DRY mode fan speed is set to Auto only.
Hi POWER OPERATION
8
To automatically control room temperature and airflow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
+L32:(5
: Start and stop the operation.
1
Press
),;
: Move the louver
in the desired vertical direction.
2
Press
FIX
: Move the
louver in the desired horizontal
direction.
3
Press
6:,1*
: For select
louver swing operation.
Vertical
(Up-Down)
Swing
Horizontal
(Left-Right)
Swing
Swing off
Up-Down
Left-Right
Swing
Pi Pi
Pi
Pi Pi
●
Vertical (Up-Down) swing
●
Horizontal (Left-Right) swing
Note:
●
Do not move the louver manually by hands or others.
●
The louver may automation positioning by some operation mode.
● Display brightness can be adjusted, follow procedure on .
 Require Wireless LAN connecting adapter which available as accessory.
1
ECO (White)
2
Wi-Fi access (White) 
3
4
Timer (White)
5
Operation Mode
- Cool (Blue)
- Heat (Orange)
1
Infrared signal emitter
2
Memory and Preset button (PRESET)
3
Start/Stop button
4
Mode select button (MODE)
5
Air fl ow/HADA CARE FLOW button
6
Fireplace/8°C button
7
ECO button
8
Comfort sleep button (COMFORT SLEEP)
9
Weekly timer (ON/OFF)
!
Temp for Weekly timer
"
On timer button (ON)
#
Set clock button (CLOCK)
$
Check button (CHECK)
%
Filter reset button (FILTER)
&
Temperature button (TEMP)
(
Swing louver button (SWING)
)
Fan speed button (FAN)
~
Set louver Left-Right button (FIX W)
+
Set louver Up-Down button (FIX X)
,
High power button (Hi POWER)
-
Power selection/Silent button (P-SEL/SILENT)
.
Program P1 - P4
/
Day/Edit button
:
Setup button (SET)
;
Off timer button (OFF)
<
Clear button (CLR)
=
Reset button (RESET)
1
2
3
4
6
5
7
8
9
0
!
@
#
$
%
&
^
t
y
*
(
w
=
)
-
e
r
q
y
Plasma Ion button (PURE)
(
see detail in the Installation Manual
).
PURE (White)
)