1-26
Operation with tape (Continued)
Timer recording using On Screen
Display
You may set up to seven timer record events within
one month of the current date.
Note
Before setting the timer make sure that you have set
the DVD+VCR clock correctly and you know which
stations you have tuned TV stations on your
DVD+VCR.
11
Insert a video cassette with protection tab into your
DVD+VCR.
The video cassette should have the window side
facing up and the arrow facing away from you.
2
Press VCR MENU.
Press
1
or
2
to select REC.
Press
ENTER/OK.
3
Press ENTER/OK to start setting the timer record
event.
If all timer record events are full press
v
or
V
to
select the event that you wish to remove and
replace.
Press
b
to delete the event.
4
Press the numbered buttons to enter the station
that you wish to record.
When selecting stations 1 - 9, press 0 first, then the
channel number; for example Stations 3 - 03. You
may also select Channels by pressing
v
or
V
.
Once selected press
B
.
If you wish to record from AUDIO IN (L/R) and
VIDEO IN on the front or from the EURO SCART
sockets on the back of your unit, press INPUT
SELECT to select for correct display (AV1, AV2 or
AV3).
5
Press the numbered buttons to enter the date of
the programme.
If you press
ENTER/OK before entering the date
you may select one of the following automated
recording features. Press
1
or
2
to select, then
press
ENTER/OK to confirm.
DLY To record every day (except Saturday and
Sunday) at the same time.
Weekly To record at the same time every week.
6
Press the numbered buttons to enter the recording start
and end times of the programme that you wish to record.
Please note your DVD+VCR uses a 24 hour clock.
e.g. 1pm will be displayed as 13:00.
You may also select the start and end times by
using
v
or
V
.
7
Press
v
or
V
to switch VPS/PDC on or off.
Press
B
to select the recording speed.
Press
v
or
V
to select the desired tape speed
(SP, IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program. IP mode is not
selected when VPS/PDC is ON.
8
Press VCR MENU to set another timer record event
and follow steps 3 to 7.
Check that the timer event details are correct.
Press
VCR MENU twice.
If
PLEASE CHECK is displayed, you have entered
incorrectly and will need to re-enter the data.
Press
++
++
//
//
11
11
to switch your DVD+VCR Standby.
TIMER will appear in the display window while your
DVD+VCR waits to make the recording.
99
Within 5 seconds, press
++
++
//
//
11
11
twice to end recording.
Notes
z If at a later date you wish to delete or change any of
the settings in timer event memory you may do so
without having to enter all the timer event information
again. Simply display the timer event screen. Use
v
or
V
to select the event that you wish to delete or
change.
Press
b
to delete the event...or
Press ENTER/OK to change; then press
b
or
B
to
select; Station, Date, Start and End times and LP.
Press
v
or
V
to enter the correct information.
z If Timer record events Overlap...
Make sure that the preset times of the timer recording
events do not overlap. If they do, the earlier programme
will always be given priority.
Example:
Programme 1 is programmed to start at 16:00 and end
at 17:00.
Programme 2 is programmed to start at 16:30 and end
at 17:30.
(In this case, Programme 1 will be recorded in its entirety,
but only the last 30 minutes of Programme 2 will be
recorded.)
z To watch a DVD while performing a timer
recording, press TV/VCR to select VCR mode.
To Next Page
Loading...
