©2024 TP-Link
7106511203 REV4.6.0
Plug the extender into a power outlet next to your router. Wait until its
Power LED turns solid on after blinking for a while.
Power On
1
3
Quick Installation Guide
Wi-Fi Range Extender
Solid On
Next to
Relocate
1. Plug in the extender about halfway between your router and the Wi-Fi dead
zone. The location you choose must be within the range of your router.
2. Wait for about 2 minutes until the Signal LED turns solid blue. If it doesn't,
relocate the extender closer to the router to achieve better signal quality.
.
Router Devices
Halfway
Blue: Suitable location
Red: Too far from router
Setup with videos
Scan QR code or visit
https://www.tp-link.com/support/setup-video/#range-extenders
and search for the setup video of your model.
Enjoy!
Note: For safety, only plug the extender in the direction as shown below.
Set Up
2
Method 3: Via a Web Browser
1. Connect your computer or smartphone to the
extender’s network TP-Link_Extender.
3. Follow web instructions to complete the setup.
2. Visit http://www.tplinkrepeater.net or
http://192.168.0.254 in a web browser. Create a
password to log in.
Method 2: Via the Tether App
1. Get the up-to-date Tether app from the Apple App
Store or Google Play, or simply scan the QR code.
2. Launch the Tether app and log in with your TP-Link ID.
If you don’t have an account, create one first.
Method 1: Via the WPS Button
1. Activate the WPS function on your router by
pressing the WPS button.
Note: If you don’t know how to do it, refer to your router’s user
manual, or you can use other methods to set it up.
The WPS button might
look like one of these:
3. Done. You can connect to the extender’s Wi-Fi.
Extended Network Names:
Router’s network name with _EXT at the end
or
Same as your EasyMesh router (see back for EasyMesh
details)
Passwords:
Same as your router
Tether
Scan for Tether
or
4. Follow app instructions to complete the setup. The
Signal LED should turn solid on, indicating successful
connection to your router.
Note: If the LED does not turn solid on, please refer to FAQ
> Q2.
3. Tap the button and select Range Extender.
My Devices
No devices found.
Choose Your Device Type
Wireless Router
Gaming Router
Range Extender
2. Within 2 minutes, press the WPS button on the
extender for 1 second, and the Signal LED starts
blinking. Wait for the Signal LED, 2.4GHz LED and 5GHz
LED to turn solid blue, indicating a successful
connection.
http://www.tplinkrepeater.net
Start
Conrm Password
Create Password
Low Middle High
Note: If only the 2.4GHz or 5GHz LED is solid blue, check to see if
the router has both 2.4GHz and 5GHz bands turned on. If both are
turned on, try WPS again or use other methods.
TP-Link_Extender
Notes:
1. If you cannot find your device, please refer to FAQ > Q1.
2. Due to Tether app updates, your actual user interface
and pathway may differ from those depicted here.
Blinking Solid On
Solid On
Tip: To place the extender for optimal Wi-Fi performance, access extender settings
via the Tether app and go to find Location Assistant, or simply scan the QR code to
visit https://www.tp-link.com/support/faq/3103/.
· Connect your devices to the extender wirelessly or via an Ethernet cable,
then enjoy the internet. The password of your extended network is the same
as your main router.
· You can also change the extender to Access Point Mode to transform your
existing wired network to a wireless one. For details, see Access Point Mode
(AP Mode) on the back page.
To Next Page
Need help?
General
