Trane 4TEE3C01A1000A - User Manual

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service information
pack upon completion of work.
HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
WARNING:
Installer’s Guide
▲
WARNING
!
SAFETY HAZARD!
THIS INFORMATION IS FOR USE BY INDIVIDUALS
HAVING ADEQUATE BACKGROUNDS OF ELECTRICAL
AND MECHANICAL EXPERIENCE. ANY ATTEMPT TO
REPAIR A CENTRAL AIR CONDITIONING PRODUCT
MAY RESULT IN PERSONAL INJURY AND/OR PROP-
ERTY DAMAGE. THE MANUFACTURER OR SELLER
CANNOT BE RESPONSIBLE FOR THE INTERPRETA-
TION OF THIS INFORMATION, NOR CAN IT ASSUME
ANY LIABILITY IN CONNECTION WITH ITS USE.
▲
CAUTION
!
EQUIPMENT DAMAGE!
TO PREVENT SHORTENING ITS SERVICE LIFE, THE
AIR HANDLER SHOULD NOT BE USED DURING THE
FINISHING PHASES OF CONSTRUCTION OR REMOD-
ELING. The low return air temperatures can lead to the
formation of condensate. Condensate in the presence
of chlorides and fluorides from paint, varnish, stains,
adhesives, cleaning compounds, and cement creates a
corrosive condition which may cause rapid deteriora-
tion of the cabinet and internal components.
Variable Speed – Communicating Air Handlers
4TEE3C01A1000A,
4TEE3C02A1000A,
4TEE3C03A1000A,
CONTENTS
General Information .............................................. 1
Installation Limitations & Recommendations ............................ 2
Two Piece Cabinet Disassembly ........................ 3
Unit Installation ...................................................... 4
Vertical Upflow ......................................................................... 4
Horizontal Right ....................................................................... 5
Duct Connections ................................................... 6
Refrigerant Piping ................................................. 6
Brazing to Evaporator Section ............................. 7
Condensate Drain Piping ...................................... 7
Electrical - Power Wiring ...................................... 8
Control Wiring ......................................................... 9
Airflow Adjustment ................................................. 9
Unit Test Mode ....................................................... 10
User Interface Menus ........................................... 11
Air Handler Flash Codes .............................. 13
Field Wiring ............................................................ 14
Electrical Connections to EAC ............................ 17
Outline Drawings .................................................. 18
Checkout Procedures .......................................... 20
A. GENERAL INFORMATION
These instructions do not cover all variations in sys-
tems or provide for every possible contingency. Should
further information be desired or particular issues arise
which are not covered sufficiently by this manual, con-
tact your local distributor or the manufacturer as listed
on the Air Handler nameplate.
These Air Handlers are shipped from the factory in the
upflow or horizontal right configuration.
18-GE14D1-5
This Air Handler can be configured for Communicating
or 24 VAC modes. Using fully Communicating or 24
VAC modes, the Air Handler can support single or multi
stage heat pump cooling only, or cooling with electric
heat applications. Combined with a communicating
Comfort Control only, the Air Handler will support a
single stage 24 VAC cooling outdoor unit.
© 2010 Trane
4TEE3C04A1000A,
4TEE3C05A1000A,
4TEE3C06A1000A,
4TEE3C07A1000A,
4TEE3C08A1000A,
4TEE3C09A1000A,
4TEE3C10A1000A
NOTE: The 4TEE3C10 air handler should NOT be
installed in the horizontal left or down flow
configuration unless the outdoor unit has an AHRI
rating with 18-GJ01D1 in the AHRI Directory. System
ratings listed without 18-GJ01D1 are for horizontal
right and upflow configurations only. The
manufacturer recommends installing only approved,
matched indoor and outdoor systems.

Trane 4TEE3C01A1000A Specifications

General

Model Number	4TEE3C01A1000A
Category	Air Handlers
Refrigerant	R-410A
Voltage	208/230V
Coil Type	Aluminum
Motor Type	PSC
Insulation	Fiberglass

Summary

Installation Limitations & Recommendations

Inspection

Check for shipping damage, report claims, and verify all components are present.

Heater Safety Caution

Warning about using only Trane-approved heaters for safe and reliable operation.

Two Piece Cabinet Disassembly

Disassembly and Reassembly Steps

Detailed steps for disassembling and reassembling the two-piece cabinet.

Unit Installation

Upflow Configuration

Instructions for installing the unit in an upflow configuration.

Narrow Coil Baffle Caution

Warning to align baffle correctly to avoid puncturing coil tubing.

Unit Installation - Horizontal Right

Horizontal Right Configuration

Instructions for installing the unit in a horizontal right configuration.

Duct Connections

Duct Connection Procedure

Connecting ducts using specified flanges and sealing for airflow.

Refrigerant Piping

Refrigerant Piping Routing

Route refrigerant piping to maintain service access and filter removal.

TXV Bulb Protection During Brazing

Protect the TXV bulb during brazing to prevent overheating and performance issues.

Brazing to Evaporator Section

Brazing Shield Usage

Use the provided brazing shield and wet it before brazing.

Tubing Unsealing Procedure

Do not unseal refrigerant tubing until ready to cut and fit lines.

Condensate Drain Piping

Level Installation and Drain Connections

Ensure level installation and proper connection of drain lines.

Drain Piping Safety and Support

Safety notes on torch use and supporting drain piping to prevent strain.

Electrical - Power Wiring

Power Wiring and Circuit Protection

Wiring requirements, circuit breaker sizing, and accessory notes.

Control Wiring

Low Voltage Wiring Lengths

Maximum recommended lengths for communicating and 24 VAC low voltage wiring.

Airflow Adjustment

Adjusting Blower Speed and Airflow

Using the User Interface to adjust airflow settings for optimal performance.

Unit Test Mode

Unit Test Mode Operation

Procedure and behavior of the unit test mode for verification.

User Interface Menu - Communicating Mode

Communicating Mode UI Navigation

Navigating and understanding the user interface menu for communicating mode.

User Interface Menu - 24 VAC Mode

Air Handler Flash Codes

Flash Code Interpretation

Understanding air handler fault and alert codes for troubleshooting.

Field Wiring - Reference Only

Communicating System Wiring Diagram

Wiring diagram for communicating systems with outdoor unit.

24 VAC Single Stage Cooling Wiring

Wiring diagram for 24 VAC single stage cooling systems.

24 VAC 2-Stage Cooling Wiring

Wiring diagram for 24 VAC 2-stage/step cooling systems.

24 VAC Single Stage Heat Pump Wiring

Wiring diagram for 24 VAC single stage heat pump systems.

24 VAC 2-Stage Heat Pump Wiring

Wiring diagram for 24 VAC 2-stage/step heat pump systems.

Electrical Connections to EAC

Electrical Safety Warning

Hazardous voltage warning; disconnect power before servicing.

EAC Connection Procedure

Step-by-step instructions for connecting an Air Cleaner (EAC).

Outline Drawing for 4 TEE3 C01-10 A

Minimum Unit Clearance Table

Table specifying required clearances to combustible materials.

Unit Dimension and Pipe Size Table

Table detailing physical dimensions and pipe sizes for different models.

Air Handler Dimensional Data

Model Height and Width Table

Table showing height (H) and width (W) for various air handler models.

Checkout Procedure

General Checkout Checklist

Checklist for verifying correct installation and operation after completion.

Supplementary Heater Checkout

Checklist for verifying correct installation and operation of supplementary heaters.