Thank you for purchasing the Traxxas EZ-Peak Plus charger. This charger features exclusive
Traxxas innovations that make charging batteries easier and safer than ever. If you have any
questions or concerns about your charger, please contact our customer support team for
fast, friendly answers and solutions. Contact information is at the bottom of this page.
WARNING! For best charging results and your safety, it is essential that you read and
understand these instructions before using the charger. Charging and discharging batteries
has the potential for serious injury and damage to property. Use care when charging and
follow all instructions and cautions.
NiMH/LiPO FAST CHARGER INSTRUCTIONS
HKC18010-R05 210721
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 1-888-TRAXXAS (Toll-free, US only) or 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com
1. Plug the charger into an AC wall outlet, and then connect
the NiMH battery as shown
2. Verify the charge settings
3. Charging
Charging Traxxas iD LiPo Batteries
Charging Traxxas iD NiMH Batteries
A. Battery iD Start/Stop
B. LiPo Charge Mode Select
C. Battery Type Select
D. Charge Rate Select
AA
BB
CC
DD
EEFF
GG
HH
Press and hold the Start button for 2
seconds. The charger will play a tone
and the green progress LED will flash,
indicating that charging has started.
The red charge progress LEDs will light
as the battery charges. Press the Start
button at any time to stop charging.
The charger will play a tone, indicating
that charging has been canceled.
Battery type
selected must
match the battery
type shown on
the battery.
Battery type selected must match the battery type shown on the battery.
Charge
Status
Charge
Progress
Charge Rate
(Amps)
E. Charger Output Port (Traxxas High-Current Connector)
F. 2S/3S Lipo Balance Ports (pull to remove cover)
G. Charge Status LED
H. Charge Progress/Charge Rate LEDs
LiPo Charging Modes
Storage charge
Makes it easy to charge or discharge the
battery to the proper storage voltage. Use this
mode whenever the battery will be stored
unused for more than 7 days.
Fast charge
Fast charges your battery without balancing
your cells. Stops charging when the rst cell
reaches peak voltage. Depending on the
battery, this may reduce the charge time by a
few minutes.
Balance charge
Always balance charge your LiPo batteries
for maximum capacity, voltage, and battery
life. This is the default setting for Traxxas iD
batteries. The EZ-Peak Plus performs a balance
charge quickly and eciently.
4. Charge cycle complete
3. Charging
Press and hold the Start button for
2 seconds. The charger will play a
tone and the green progress LED
will flash, indicating that charging
has started. The red charge progress
LEDs will light as the battery charges.
Press the Start button at any time to
stop charging. The charger will play
a tone, indicating that charging has
been canceled.
4. Charge cycle complete
Charging
(flashing)
1. Plug the charger into an AC wall outlet, and then connect
the LiPo battery as shown
2. Verify charge settings
Battery Type
Charge Rate
Start
Charge Rate Start
Battery Type
Charge Mode
Charging
(flashing)
Charge Cycle Progress
Cycle Complete
(solid)
Cycle Complete
(solid)
The EZ Peak
Plus will trickle
charge your NiMH battery
at up to 200mA for 12 hours
after the charge cycle is complete.
Covers Part #2970 (USA)
Part #2970X (International)
The charger will
recognize the iD
battery and show
you the charge
settings.
The charger will play a
“charge complete” tone
to indicate charging
is complete. The alert
tone will play 3 times
and stop.
The charger will
recognize the iD
battery and show
you the charge
settings.
The charger will play a
“charge complete” tone
to indicate charging
is complete. The alert
tone will play 3 times
and stop.
Charge Cycle Progress
To Next Page
Need help?
General
Weight and Dimensions
