Trimble R10 User Manual

TrimbleR10ReceiverWebHelp
Thereceiveralsosupportsthird‐partytransparentradiosandthird‐partycellularmodems.
Touseanexternalradiowiththereceiver,youneedanexternalpowersourcefortheradio—
exceptfortheSNB900radio,whichcontainsaninternalbattery.Toconfiguretheradiomodem
separately,use
theexternalradio’sconfigurationprogram,orthedisplayandkeypad.
ConfiguringtheReceiver
Configuringthereceiver
Youcanconfigurethereceiverinanumberofways.Thesetopicsdescribethedifferent
configurationmethods,andexplainswhenandwhyeachmethodisused.
TrimbleAccesssoftwareislikelytobeyourmaintooltosetupandoperatethereceiveronadaily
basis.Allrequiredfieldconfigurations
arehandledthroughtheTrimbleAccesssoftwarerunningon
aTrimbleTablet,TSC3,orTrimbleCUcontroller.Formoreinformation,refertotheTrimbleAccess
SoftwareUserGuide.
Configuringthereceivertousespecificsettingswhenitisturnedon
Thepowerupapplicationfile(Power_up.cfg)isusedtosetthereceivertoaspecificconfiguration
anytimetheunitisturnedon.
Inthisfile,youcanselecttoresetthereceivertodefaultsbeforethepowerupsettingsareapplied.
Thisensuresthatwhen yourestartthereceiver,it
alwaysresetstofactorydefaultsbeforeapplying
thepowerupapplicationfile.
Alternatively,youcanspecifythatthepowerupsettingsareappliedimmediatelyafterthecurrent
applicationfile’ssettingshavebeenapplied.Restartingthereceiverresultsinaconfigurationthat
usesyourdefaultsettingsfortheoptionsyoudefine
inthepowerupfile,butthecurrentsettings
forallotheroptions.
Bydefault,thereisnopower_upapplicationfileonthereceiver.Touseapowerupapplicationfile,
youmustcreateandsaveapower_upapplicationfileintheGPSConfiguratorsoftware.Ifyousave
thisfileto
disk,thefileiscalledpower_up.cfg.Theextension.cfgisused,byconvention,toidentify
applicationfilesontheofficecomputer.Whenyoutransferthisfiletothereceiver,thefileissaved
onthereceiveraspower_up,andbecomesthenewpowerupfile.
Configuringthereceiverusingapplicationfiles
Anapplicationfilecontainsinformationforconfiguringareceiver.Toconfigureareceiverusingan
applicationfile,youneedtocreatetheapplicationfile,transferittothereceiverandthenapplythe
file’ssettings.TheGPSConfiguratorsoftwaredoesthisautomaticallywhenyouworkwith
configurationfiles.
Overview
Anapplication
fileisorganizedintorecords.Eachrecordstoresconfigurationinformationfora
particularareaofreceiveroperation.Applicationfilescanincludethefollowingrecords:

Trimble R10 Specifications

General

Channels	440
RTK Horizontal Accuracy	8 mm + 1 ppm RMS
RTK Vertical Accuracy	15 mm + 1 ppm RMS
Operating Temperature	-40 °C to +65 °C
L1 C/A Code	Yes
L2E	Yes
L2C	Yes
L5	Yes
Beacon	No
FM Radio	No
WAAS	Yes
MSAS	Yes
EGNOS	Yes
Storage Temperature	-40 °C to +75 °C
Ingress Protection	IP67
Positioning Accuracy (Static) - Horizontal	3 mm + 0.5 ppm RMS
Positioning Accuracy (Static) - Vertical	5 mm + 0.5 ppm RMS
Signal Tracking	BeiDou
RTK Initialization	< 8 seconds
Battery Life	Up to 7 hours
SBAS Accuracy	50 cm
Glonass Code	L1 C/A, L2 C/A
Communications	Bluetooth