Triumph TR2 - Page 289

BODY
Fig . 1
Fig . 2
Fig . 3
Fig . 4
Fig . 5
Fig . 6
Fig
. 7
Fig . 8
INDEX
Page
......
...... ......
......
......
Body Mounting Points ............ l
...... ......
......
......
......
......
To remove Body ...... 1
...... ......
...... ......
...... ......
......
To fit Body ...... 2
......
......
...... ......
......
......
Battery Box Drain ...... 2
.....
......
To remove and Dismantle Front Bumper ............ 2
......
...... ...... ......
......
To fit Front Bumper ............
3
.....
......
To remove Rear Over-Riders and Brackets ............
3
......
......
...... ......
......
To fit Rear Over-Riders ...... 3
......
...... .....
......
......
......
To remove Front Wing 4
......
...... ...... ......
...... ......
To fit Front Wing ...... 4
......
...... ...... ......
...... ......
To remove Rear Wing 4
...... ......
..... ......
......
......
To fit Rear Wing ...... 4
...... ......
...... ......
......
......
To remove Bonnet Lid 4
......
...... ......
......
...... .....
To fit Bonnet Lid ...... 4
......
...... ...... ......
......
To remove Front Apron ...... 5
......
...... .....
...... ......
......
To fit Front Apron ...... 5
...... ......
...... ......
Adjustment of Bonnet Locks ............
5
......
...... ......
......
...... ......
To remove Windscreen 5
......
...... ......
...... ......
......
To fit Windscreen ...... 6
......
...... ...... ......
......
To fit Aero-Windscreen ...... 6
...... ......
...... ......
......
......
......
To remove Door 6
......
...... ...... ......
......
...... ......
To fit Door ...... 6
......
...... ......
......
...... ......
Front Door Sealing ...... 6
......
......
......
......
...... ......
To remove Door Lock 6
......
...... ...... ......
...... ......
To fit Door Lock 6
...... ......
...... ......
......
To remove Gearbox Gel 7
......
...... ......
......
...... ......
To fit Gearbox Tunnel 8
......
...... ...... ......
......
To remove Hood and Fittings
8
......
...... ......
...... ......
To fit Hood and Fittings ...... 8
...... ...... ......
......
......
Water Sealing of Hood Seams
8
......
...... ......
......
Adjustment of Side Curtains ............
9
.....
To prepare car for Fibreglass Hard Top Canopy ............ 9
...... ...... ...... ......
Fitting Fibreglass Hard Top Canopy
10
...... ...... ......
To remove Fibreglass Hard Top Canopy ...... 11
...... ......
To remove and Dismantle Luggage Boot Lid ...... 11
......
...... ......
To fit Luggage Boot Lid ...... 11
...... ...... ......
To remove and Dismantle Spare wheel id'."
11
...... ......
...... ......
To assemble Spare Wheel Lid
11
......
......
To fit Smiths Circular Heater CHS 92014 ............
12
LIST OF ILLUSTRATIONS
Page
Body mounting points
............ 1
Battery box drain ...... .... 3
Front door water sealing ... 7
..... Hard top windscreen brackets 9
Bridge pieces in position ...... 10
Protection caps
in position ... 10
... Hard top rear attachments 10
Fitting tap extension ...... ...... 12
Page
Fig
. 9 Assembling water pipe connectors 12
Fig . 10 Releasing steering support rod ...... 12
Fig . 11 Location of heater control switch 15
Fig . 12 The heater unit ready for assembly 15
.....
Fig . 13 Fitting heater hoses ...... 14
. ............
Fig 14 Heater unit in position l
Fig
. 15 Showing position water pipes ...... 11
Fig
. 16 Exploded view of heater kit ...... l!