Turbo Air Smart 7 - User Manual

Questions and Answers

L
Luke RobertsAug 19, 2025
What to do if Turbo Air Smart 7 fan(s) will not operate?
- D
  Deborah GarciaAug 19, 2025
  If the fan(s) won't operate, consider the following: * The main switch might be open: close the switch. * Blown fuses: replace the fuses and check for short circuits or overload conditions. * Defective motor: replace the motor. * The coil does not get cold enough to reset the thermostat: adjust the fan delay setting of the control. * Controller or sensor defective: replace the defective component. * The unit is in a defrost cycle: wait for completion of the cycle.
C
colleen16Aug 22, 2025
What causes a Turbo Air Smart 7 to have high discharge pressure?
- A
  Alicia TurnerAug 22, 2025
  High discharge pressure can be caused by: * Non-condensable substances in the system: remove them. * Too much refrigerant: remove the excess refrigerant. * The fan not running: check the electrical circuit and fuse. * A dirty condenser coil: clean the condenser coil. * The liquid line solenoid not open: repair or replace the coil.
P
Phillip RamirezAug 25, 2025
Why is my Turbo Air Smart 7 room temperature high?
- A
  Alyssa AvilaAug 25, 2025
  If the room temperature is too high, it could be due to: * The controller temperature being set too high: adjust the control. * Superheat being too high: check and reset for proper superheat. * Insufficient refrigerant: check for leaks and add charge. * The evaporator coil being iced: manually defrost the coil and check the defrost controls for malfunction.
F
Frank WilliamsAug 27, 2025
What causes noisy compressor in Turbo Air Smart 7?
- E
  Erin ToddAug 27, 2025
  A noisy compressor can be caused by: * Flooding of liquid refrigerant into the crankcase: check the expansion valve setting. * Worn compressor: replace the compressor.
B
bryantlarryAug 30, 2025
What to do if there is ice accumulating in pan of Turbo Air Smart 7 Refrigerator?
- C
  Casey StephensAug 30, 2025
  If ice is accumulating in the pan: * Check for defective heaters and replace if necessary. * Ensure the unit is installed properly and is level; adjust if needed. * Clean the drain line if it's plugged. * Replace the defective control if necessary.
D
David TaylorSep 2, 2025
What causes low suction pressure in Turbo Air Smart 7 Refrigerator?
- A
  Amanda LeSep 2, 2025
  Low suction pressure may be due to: * Expansion valve malfunctioning: check and reset for proper superheat. * Lack of refrigerant: check for leaks and add charge.
L
Lauren CrosbySep 4, 2025
How to fix ice accumulating ceiling around grill in Turbo Air Refrigerator?
- R
  Robin PittmanSep 4, 2025
  Ice accumulating around the grill can be due to: * Defrost duration being too long: adjust the defrost termination temperature. * Fan delay not delaying fans after the defrost period: adjust the fan delay setting or replace the sensor. * Defective defrost control or sensor: replace the defective component. * Too many defrosts: adjust the number of defrosts.
A
amy75Sep 7, 2025
What causes Turbo Air Refrigerator to have low discharge pressure?
- G
  gonzalezjoshuaSep 7, 2025
  Low discharge pressure can result from: * Insufficient refrigerant: check for leaks and add charge. * Low suction pressure: See corrective steps for low suction pressure.
C
Connie HarrisSep 10, 2025
What causes high suction pressure in Turbo Air Smart 7 Refrigerator?
- S
  stephengonzalezSep 10, 2025
  High suction pressure can be caused by: * Excessive loads: reduce the load. * Expansion valve overfeeding: check bulb location and clamping and adjust superheat.
A
Ashley EricksonSep 12, 2025
What to do if coil not clearing of frost during defrost cycle in Turbo Air Refrigerator?
- T
  Tara RichardSep 12, 2025
  If the coil isn't clearing frost during the defrost cycle: * Check heater operation if the coil temperature isn't getting above freezing during defrost. * Adjust the control for more defrost cycles if there are not enough defrost cycles per day. * Adjust the defrost control and duration setting if the defrost cycle is too short. * Replace the defective component if there is a defective defrost control or sensor.