Tyco Security Products Software House IP-ACM - User Manual

IP-ACM Ethernet Door Module
Quick Start Guide
VERSION C0
PART NUMBER 8200-1200-02
MARCH 2016
IP-ACM Ethernet Door Module
The IP-ACM module provides connection and management of the access control for two doors through inputs, outputs,
and reader interfaces. Supporting two readers through Power over Ethernet (PoE), the IP-ACM communicates to the
Ultra General Control Module (GCM) over TCP/IP. The IP-ACM module also has AES256 network encryption from the
unit to the GCM. The encryption settings are determined by the GCM configuration. The maximum number of IP-ACM
modules supported per GCM is 32.
Part Number Description
IP-ACM2-MB IP-ACM, 2 Reader, board only
IP-ACM2-EM IP-ACM, 2 Reader in metal enclosure
IP-ACM2-EP
1
IP-ACM, 2 Reader in plastic enclosure
IP-ACM2-CAN IP-ACM metal enclosure without board
IP-ACM2-CAN-P
2
IP-ACM plastic enclosure without board
Table 1:Part numbers and descriptions of IP-ACM and enclosures
Installation Requirements
Ensure the site is ready:
■ The module installation must be performed by a certified installer and must be installed within the same protected
premise as the controlling GCM.
■ For a UL-compliant installation, the power supply must be UL Listed to UL 294 and/or UL 603, low voltage Class 2
power limited with appropriate ratings.
■ All interconnecting devices must be UL Listed, low voltage Class 2 power limited.
■ The site must be approved and all wiring must comply with UL requirements and other codes, as appropriate.
Installation shall be in accordance with the National Electric Code, ANSI/NFPA 70-1993.
■ In this installation, the enclosure is mounted directly to a wall or uni-strut using suitable user-supplied hardware.
■ The anchoring system must be capable of sustaining, a proof load four times that of the assembly. Refer to the
enclosure dimensions for information on the weight of enclosures. This weight does not include the cables.
1
Not UL listed.
2
Not UL listed.
1

Summary

IP-ACM Ethernet Door Module Description

Installation Requirements

Electrostatic Sensitive Devices (ESD) Precautions

Precautions for handling sensitive electronic components to prevent damage from static discharge.

Life Safety Requirement

A fail-safe override mechanism must be installed at each card reader exit for safety.

Burglar Alarm Installation Requirements

Specific requirements for IP-ACM installations related to burglar alarm systems.

Enclosures

Plastic Enclosure Details

Details and dimensions for the plastic enclosure used with the IP-ACM module.

Installing the Plastic Enclosure

Step-by-step instructions for mounting the IP-ACM module within the plastic enclosure.

Metal Enclosure Details

Details and dimensions for the metal enclosure used with the IP-ACM module.

Installing the Metal Enclosure

Step-by-step instructions for mounting the IP-ACM module within the metal enclosure.

Grounding and Safety

Grounding Requirements

Essential grounding procedures and compliance with electrical codes for proper installation.

Power Disconnection Warning

Important safety instruction to disconnect all power sources before modifying wiring.

Power and Wiring Requirements

Configuration and Operation

Supervision Wiring

Diagrams and explanations for supervised input wiring configurations.

Environmental Requirements

Specifies the operational temperature range and indoor use limitations for the IP-ACM.

Initial Configuration Overview

Procedures for the initial setup and configuration of the IP-ACM module.

MAC Address Location

Information on where to find the MAC address of the IP-ACM module.

Normal Operation Mode Configuration

Steps to configure the IP-ACM for normal operation via a DHCP network.

Standalone Configuration Mode

Steps to configure the IP-ACM with a static IP address without DHCP.

IP-ACM Hardware Overview

Description of the IP-ACM board features, switches, jumpers, and connectors.

Wiegand Wiring and Supported Devices

Wiegand Wiring Diagram

Visual representation of Wiegand reader connections and LED status.

Supported Readers and Modules

List of UL-supported Wiegand readers, RS-485 RM Bus devices, and accessory modules.

Regulatory Information

Canadian Radio Emissions

Compliance with Canadian radio noise emissions regulations for digital apparatus.

FCC Digital Device Limitations

Compliance with FCC rules regarding radio and television interference.

Manufacturers Caution

Warning that unauthorized modifications may void the user's authority to operate the equipment.

Tyco Security Products Software House IP-ACM Specifications

General

Model	IP-ACM
Category	IP Access Controllers
Network Interface	Ethernet 10/100Base-T
Power Supply	12 to 24 VDC
Input Voltage	12-24 VDC
Operating Temperature	-4° to 158°F (-20° to 70°C)
Humidity	0% to 95% non-condensing
Communication Protocol	TCP/IP
Certifications	UL294, CE, FCC