EasyManua.ls Logo

U-Line H-5440 - User Manual

U-Line H-5440
12 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PAGE 1 OF 12 0219 IH-5439
π H-5439, H-5440
STRADDLE STACKER
1-800-295-5510
uline.com
TECHNICAL DATA
DESCRIPTION H-5439 H-5440
Mast Height (Lowered) 77¾" 91½"
Mast Height (Raised) 80" 160"
Lifting Height, Max. 63" 137"
Lifting Height, Min. 2
1
⁄8"
Weight Capacity, Max. 2,200 LBS.
Overall Length 70"
Overall Width 42½ - 54½"
Fork Size – Length 42"
Fork Size – Width 4"
Forks Adjustable Width (Inside Dim.) 1/2 - 20"
Forks Adjustable Width (Outside Dim.) 8½ - 28"
Straddle Legs (Inside Dim.) 37¾ - 48¾"
Straddle Legs (Outside Dim.) 43¾ - 54¾"
Straddle Leg Height 5⁄"
Para en Español, vea páginas 5-8.
Pour le français, consulter les pages 9-12.
SAFETY
1. Operator should read all warning signs and
instructions here and on the stacker before use.
2. Do not operate stacker unless you are familiar with it
and have been trained or authorized to do so.
3. This is a manual push truck. Operator must be able
to safely move, control and stop a fully-loaded unit
by themselves.
4. Do not use on uneven ground or in a dangerous
environment.
5. Do not lift people with the stacker.
6. When forks are in motion, no one should stand
under the forks or pass below the forks.
7. Do not move the stacker unless the forks are 12 inches
or less off the ground.
8. Keep a two-foot distance between the stacker and
any person not operating the stacker.
9. The weight of goods should be evenly distributed
between the two forks.
10. Do not load over the maximum capacity.
11. Keep the forks in the lowest position when not in use.
12. Locking caster is designed to help prevent rolling
when unit is not in use. It is not designed to slow
down or stop the unit.

Table of Contents

Questions and Answers

  • L
    Lisa ShortAug 7, 2025
    What to do if the motor of my U-Line H-5440 does not turn on?
    • P
      petersonmarieAug 7, 2025
      If the motor of your U-Line Forklifts doesn't turn on, it might be due to several reasons. First, check if the Emergency Shut-Off is pressed down and turn it clockwise to switch the power on. It's also possible that the voltage is too low, so ensure the stacker is adequately charged. Inspect all wire connections for looseness and reconnect them if necessary. Lastly, a bad connector to the DC motor could be the culprit, in which case you should replace it.
  • J
    Jason OrtizAug 12, 2025
    Why is my U-Line H-5440 Forklifts battery not charging?
    • B
      Brian CobbAug 12, 2025
      If your U-Line Forklifts battery isn't charging, the issue might stem from a faulty battery which requires replacement. Alternatively, the charging plug could be loose, so inspect the connection and reattach it securely if needed.
  • F
    flynnAug 17, 2025
    What to do if forks descend without engaging the lower lever in U-Line Forklifts?
    • C
      Christopher ReyesAug 18, 2025
      If the forks on your U-Line Forklifts are descending without engaging the lower lever, the problem could be due to impurities in the oil, preventing the release valve from closing tightly; in this case, change the oil. Another cause could be worn or damaged seals, which would require replacing the seals. Lastly, the release valve itself might be damaged, necessitating a replacement.
  • J
    Jessica TurnerAug 22, 2025
    Why are there leaks in my U-Line Forklifts?
    • Y
      Yolanda DuncanAug 22, 2025
      If you notice leaks in your U-Line Forklifts, it's likely due to worn or damaged seals, which should be replaced. Another potential cause is cracked or worn piston parts that are too small, requiring replacement as necessary.
  • A
    Anna CookAug 27, 2025
    What to do if the forks do not go down in U-Line H-5440 Forklifts?
    • P
      pamela92Aug 28, 2025
      If the forks on your U-Line Forklifts do not go down, several factors could be responsible. The piston rod or mast might be damaged due to incorrect loading or overloading, necessitating a replacement. Another potential issue is a rusted or jammed piston rod from keeping the fork in the up position for extended periods, which can be resolved by lubricating the piston rod and always keeping the fork in the lowest position when not in use. Lastly, the release valve of the pump may not be opened; check it and replace it if damaged.
  • K
    kathyhicksSep 1, 2025
    How to fix forks not reaching maximum height on U-Line H-5440 Forklifts?
    • J
      jbraySep 1, 2025
      If the forks on your U-Line Forklifts aren't reaching their maximum height, it could be due to insufficient hydraulic oil or impurities in the oil. Try adding more hydraulic oil or changing the oil completely.

Summary

Technical Data

Load Capacity

Control Panel

Charging the Battery

Instructions

Adjusting the Legs

Procedure to adjust the stacker legs to the desired position within the body's slot.

Adjusting the Forks

Procedure to lift and slide the front of the fork to the desired position.

Maintenance

Troubleshooting

U-Line H-5440 Specifications

General IconGeneral
BrandU-Line
ModelH-5440
CategoryForklifts
LanguageEnglish

Related product manuals