EasyManua.ls Logo

U-Line H-8921 - User Manual

U-Line H-8921
9 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PAGE 1 OF 9 1121 IH-2708
INDUSTRIAL
PALLET TRUCK
1-800-295-5510
uline.com
H-2708, H-2900, H-3045
H-5387, H-6710, H-7504
H-8921, H-9612
OPERATION
TECHNICAL DATA
WARNING! Operator must read and understand
instructions here and on truck prior to use.
On the handle of the pallet truck, you will find the
control lever, which can be set in three positions.
(See Figure 1)
- LOWER = to lower the forks
- NEUTRAL = to move the load
- RAISE = to raise the forks
1. If the forks elevate while pumping in the NEUTRAL
position, turn the setting screw clockwise until
pumping the handle does not raise the forks and the
NEUTRAL position functions correctly.
2. If the forks descend while pumping in the NEUTRAL
position, turn the setting screw counterclockwise until
the forks do not lower.
3. If the forks do not descend when the control lever is in
the LOWER position, turn the setting screw clockwise
until raising the control lever lowers the forks. Then
check the NEUTRAL position as per step 1 and 2.
4. If the forks do not lift while pumping in the RAISE
position, turn the setting screw counterclockwise
until the forks elevate while pumping in the RAISED
position. Then check the NEUTRAL and LOWER
position as per steps 1, 2 and 3.
NOTE: When viewing the truck from the handle
side, the setting screw is located on the right
side of the pump above the right wheel. The
truck will lower faster or slower depending on
how far in or out the screw is adjusted.
Figure 1
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
MODEL H-2708/H-2900/H-3045/H-5387/H-7504 H-6710 H-8921 H-9612
Capacity 5,500 lbs. 5,500 lbs. 5,500 lbs. 4,400 lbs.
Max. Fork Height 7.5" 7.5" 7.5" 5.6"
Min. Fork Height 3.0" 3.0" 3.0" 2.0"
Fork Length 48" 48" 72" 48"
Overall Fork Width 27" 21" 27" 27"
Fork Wheel Diameter 3" Polyurethane 3" Polyurethane 3" Polyurethane 2" Polyurethane
Steering Wheel Diameter 7" Polyurethane 7" Polyurethane 7" Polyurethane 7" Polyurethane
Net Weight 165 lbs. 152 lbs. 258 lbs. 203 lbs.

Table of Contents

Questions and Answers

  • W
    Wayne RobinsonAug 15, 2025
    Why are my U-Line H-8921 Trucks leaking?
    • R
      robertperezAug 15, 2025
      If your U-Line Trucks are leaking, it's likely due to worn or damaged seals. Replace the seals with new ones. Also, check for cracked or worn-out parts and replace them as needed.
  • S
    Steven WheelerAug 18, 2025
    Why do the forks descend without being lowered on my U-Line Lifting Systems?
    • J
      jasonjenkinsAug 18, 2025
      If the forks on your U-Line Lifting Systems descend without being lowered, it could be due to impurities in the oil preventing the discharge valve from closing properly. Try changing the oil. Another possible cause is air in the hydraulic oil; in this case, you should expel the air.
  • M
    Mr. Jeremiah SmithAug 21, 2025
    What to do if my U-Line Lifting Systems has leaks?
    • M
      martinthomasAug 21, 2025
      Leaks in your U-Line Lifting Systems can be caused by worn out or damaged seals. Replace the seals with new ones. Also, check for cracked or worn out parts and replace them as needed.
  • W
    William StevensAug 25, 2025
    Why do the forks on my U-Line Lifting Systems not raise?
    • M
      Meghan RiveraAug 26, 2025
      If the forks on your U-Line Lifting Systems do not raise, it could be due to several reasons. First, check if there is enough hydraulic oil and add more if needed. The oil might have impurities, requiring an oil change. The discharge valve may be out of adjustment, so adjust the setting screw. Additionally, air in the hydraulic oil can cause this issue; expel the air.
  • K
    kleindonnaAug 28, 2025
    What to do if the forks do not descend on my U-Line Lifting Systems?
    • L
      lmorganAug 28, 2025
      If the forks on your U-Line Lifting Systems do not descend, it could be because the rod and/or the cylinder are deformed due to a seriously unbalanced load. Replace the rod or cylinder. Another possibility is that a part has been broken or deformed from an unbalanced load; repair or replace the component. Also, the setting screw may not be in the correct position, so adjust it.
  • A
    Andrew SullivanAug 31, 2025
    What to do if the forks on my U-Line H-8921 Trucks do not raise?
    • J
      Joshua Ramsey PhDSep 1, 2025
      If the forks on your U-Line Trucks aren't raising, several issues could be the cause. First, check if there is enough hydraulic oil and add more if needed. Secondly, the oil may have impurities, in which case you should change the oil. Other potential causes include a discharge valve that is out of adjustment, which requires adjusting the setting screw, or air in the hydraulic oil, which needs to be expelled.
  • S
    smithmichelleSep 4, 2025
    Why do the forks on my U-Line H-8921 descend without being lowered?
    • C
      Cindy AlvarezSep 4, 2025
      If the forks on your U-Line Trucks descend without being lowered, it could be due to several reasons: impurities in the oil may be preventing the discharge valve from closing properly, so try changing the oil. Another possibility is air in the hydraulic oil, which needs to be expelled. Worn or damaged seals can also cause this issue, so replace them. Finally, check if the setting screw is in the correct position and adjust it if necessary.
  • M
    Michael GarrisonSep 7, 2025
    What to do if the forks on my U-Line Trucks do not descend?
    • L
      Lisa WilsonSep 7, 2025
      If the forks on your U-Line Trucks aren't descending, this may be because the rod and/or the cylinder are deformed due to a seriously unbalanced load, in which case you should replace the rod or cylinder. Another cause may be that a part has been broken or deformed resulting from an unbalanced load, so you should repair or replace the component. Also, ensure that the setting screw is in the correct position and adjust it if necessary.
  • M
    Miss Susan MorenoSep 12, 2025
    How to fix forks on U-Line Trucks not lifting to maximum height?
    • R
      Raymond RyanSep 12, 2025
      If the forks on your U-Line Trucks aren't lifting to their maximum height, it's likely that there isn't enough hydraulic oil. Add more oil to resolve this issue.

U-Line H-8921 Specifications

General IconGeneral
BrandU-Line
ModelH-8921
CategoryTrucks
LanguageEnglish

Related product manuals