EasyManua.ls Logo

U-Line ZEBRA ZD410 - User Manual

U-Line ZEBRA ZD410
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PAGE 1 OF 18 0518 IH-6323
π H-6323
ZEBRA DIRECT
THERMAL PRINTER
1-800-295-5510
uline.com
PARTS
EXTERNAL PARTS DIAGRAM
Documentation Printer
Control Panel
Release Latches
DC Power
Receptacle
Power Switch
Fan-Fold
Media Entry Slot
Interface and
Connectivity
Module Slot Access
Power CordPower Supply USB Cable
NOTE: Save the carton and all packing
materials for storage or in case the
printer needs to be returned to the
manufacturer.
ZEBRA MODEL NO. ZD410
Para Español, vea páginas 7-12.
Pour le français, consulter les pages 13-18.

Table of Contents

Questions and Answers

  • B
    Brian Curry MDJul 28, 2025
    Why is the barcode on my U-Line ZEBRA ZD410 Printer label not scanning?
    • R
      Roberta WilliamsJul 28, 2025
      The barcode on the label may not scan because there is not enough blank space around it. Leave at least 1/8 in. of blank space around the barcode (referred to as the quiet zone) and other printed areas on the label and between the barcode and the edge of the label. This requirement varies by barcode type. Another reason could be a void or missing print in a barcode, text or graphic in a printed form. In this case, perform Cleaning the Printer to remove contaminants on the printheads. Reprint and test the barcode. Use the Printer and Network Configuration Reports from Cleaning the Printer to see if the printhead has damaged printhead elements. Verify that the large black bar on the bottom of the printed test label does not have any streaks or voids after thoroughly cleaning the printhead.
  • E
    erik44Aug 7, 2025
    What to do if my U-Line Printer has general print quality issues?
    • P
      pittshannahAug 7, 2025
      If your printed image doesn't look right, it could be due to several reasons: * The printhead might be dirty, in which case you should clean it. * Ensure you're using the power supply that came with the printer. * The printhead may be worn out and need replacement. Note that using unapproved media may shorten its life or damage it. * The platen (drive) roller may need cleaning or replacement.
  • M
    Monica WarrenAug 18, 2025
    Why is there vertical image or label drift on my U-Line ZEBRA ZD410 Printer?
    • V
      Vicki PonceAug 18, 2025
      Vertical image or label drift can occur due to several reasons: * The platen (drive) roller might be dirty, so clean the printhead and platen roller. * The media may be loaded incorrectly, so ensure it is loaded correctly. * You might be using incompatible media. Use media that meets the printer specifications, ensuring that the inter-label gaps or notches are 3 to 4 mm and consistently placed.

Summary

Parts Overview

External Parts Diagram

Internal Parts Diagram

Checking the Printer

Connecting to Power

Loading Media Roll

Printing a Test Label

Print a Configuration Label

Prints printer and network configuration reports for diagnostics and setup.

Cleaning Printer

Troubleshooting

U-Line ZEBRA ZD410 Specifications

General IconGeneral
Printer TypeDirect Thermal
Print Resolution203 dpi
Print Width4.09 inches
ConnectivityUSB
Media TypesLabels, Tags, Receipts
Programming LanguagesZPL
Supported Barcode TypesCode 128, Code 39, QR Code, Data Matrix, UPC-A, UPC-E, EAN-8, EAN-13, PDF417
Operating Temperature40° to 104° F / 4.4° to 40° C
Storage Temperature-40°F to 140°F (-40°C to 60°C)

Related product manuals