How to troubleshoot a UHP NETWORKS Network Router that doesn't work?
If your UHP NETWORKS Network Router isn't working, there could be several reasons: * The AC power might be beyond allowed limits, in which case you should check the AC power voltage. * The power cord could be broken; inspect the AC cable and replace it if necessary. * There might be a router failure. Check the AC cables.
What to do if my UHP NETWORKS UHP-200 restarts every 3-5 seconds?
If your UHP NETWORKS Network Router restarts frequently, the issue might be: * A short-circuit in the transmit cable. Disconnect and check the Tx cable. * A software failure. Reset the software to factory defaults.
What to do if the ERROR indicator lights constantly after power on in my UHP NETWORKS UHP-200 Network Router?
If the ERROR indicator light remains on after powering on your UHP NETWORKS Network Router, it suggests the router can’t start the software. Try pressing the RESET button on the rear panel of the router.
Why is my UHP NETWORKS UHP-200 Network Router not transmitting, even with normal reception?
If your UHP NETWORKS Network Router isn't transmitting despite normal reception, it could be due to: * Incorrect network settings. Check the Tx frequency and symbol rate of the modulator, and ensure that transmission is enabled.
What to do if my UHP NETWORKS UHP-200 station is not transmitting, even though reception is normal and the TX indicator is blinking?
If your UHP NETWORKS Network Router station isn't transmitting, even though reception is normal, the LOCK indicator is lit, and the TX indicator is blinking, it could be due to: * IF Tx cable failure. Check the Tx cable and ensure its connectors are properly connected to the BUC and the router. * BUC is not powered. Check if BUC power is switched on. Disconnect Tx IF cable from BUC and make sure that 24 VDC is available on the connector. * BUC failure. Replace the BUC on the spare one.
What causes a high rate of errors on the Rx path on a UHP NETWORKS UHP-200 Network Router?
A high error rate on the Rx path of your UHP NETWORKS Network Router, indicated by the LOCK indicator not lighting constantly, can be caused by: * Bad weather conditions. Reception quality may temporarily decrease during heavy rainfall or thunderstorms. Check for snow or ice on the antenna surface and feed horn. * Low signal to noise level. Check C/N in demodulator’s statistics. Verify if the antenna is properly pointed to the satellite and there are no obstacles in the direction to the satellite. Check the integrity of the film of antenna’s feed horn and absence of moisture in it. * Low Rx carrier level Interferences. Check Eb/No in demodulator’s statistics.
Why is there no reception from the satellite on my UHP NETWORKS UHP-200?
If your UHP NETWORKS Network Router isn't receiving from the satellite (LOCK indicator is off, with single ERROR indicator flashes), possible causes include: * Incorrect configuration. Verify the Rx frequency and symbol rate. * IF cable failure. Check the Rx cable, ensuring connectors are properly connected to the LNB and the router. * LNB is not powered. Check if LNB power is switched on. Disconnect Rx IF cable from LNB and make sure that 12-18 VDC is available on the connector. Check Rx level in the statistic of the demodulator. * No carrier on the satellite or its level is insufficient. Verify availability of the carrier and its level with spectrum analyzer. * Low Rx carrier level. Measure carrier signal to noise level with a spectrum analyzer. Verify if antenna is properly p...
Specifies the expected expertise for users operating VSAT networks.
Defines the scope and version of the manual for UHP-200 routers.
States the intellectual property rights of the document's content.
Provides a high-level view of the UHP satellite routers and their capabilities.
Lists required items for configuring and monitoring the satellite router.
Details product markings and warranty voiding conditions.
Lists items included in the standard UHP-200 router package.
Outlines the router's structure and functional blocks.
Describes router interfaces and indicator locations.
Lists the main components and modules of the UHP-200 router.
Details the specifications for the AC power input.
Explains the purpose of optional expansion modules.
Describes LAN port functions, bit rates, and indicators.
Explains the console port for local device control via USB.
Details the TX OUT connector specifications and associated warnings.
Explains the function of the reset button for normal and factory resets.
Describes LNB connection inputs and power supply capabilities.
Explains the meaning of SYSTEM and ERROR indicator status lights.
Explains LOCK, RX1, RX2, and TX indicators for status monitoring.
Lists the specified operating parameters and constraints for the router.
Outlines essential steps before using the router.
Details how to unpack the router safely and check for damage.
Guides on rack mounting and ensuring adequate ventilation.
Explains how to connect cables and peripheral devices to the router.
Describes the startup sequence and initial status indicators.
Guides on accessing the router configuration via a web browser.
Explains local access and configuration through the USB console port.
Details how to access and configure the router remotely via Telnet.
Refers to separate manuals for command-line interface usage.
Explains how to extend router functionality by updating the software.
Details the procedure for disconnecting the router from power.
Provides essential safety guidelines for using the device.
Outlines emergency procedures for fire incidents involving the router.
Presents a table of common issues, possible reasons, and recommended actions.
Explains the procedure to reset the router to its factory default configuration.
General| Model | UHP-200 |
|---|---|
| Wireless Standard | Wi-Fi 5 (802.11ac) |
| Antenna Type | Internal |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Data Protocols | DVB-S2X, TDMA |
| Modulation | QPSK, 8PSK, 16APSK, 32APSK, QAM |
| Frequency Range | 950-2150 MHz (L-band) |
| Symbol Rate | Up to 72 Msps |
| Forward Error Correction (FEC) | LDPC/BCH |
| IP Processing | Advanced IP routing and traffic management |
| Management | Web GUI, SNMP, CLI |
| Operating Temperature | -40°C to +60°C |
| Ports | F-connector, 4x Ethernet, USB |
| Wireless | Yes, Wi-Fi 5 (802.11ac) |
| VPN Support | IPSec, PPTP, L2TP |
| Firewall | Stateful Packet Inspection (SPI) |
| QoS Support | Yes |
| Dimensions | 200 x 150 x 40 mm |
| Weight | 0.8 kg |
To Next Page
