Uni-ram UG5000W - User Manual

Other manuals for Uni-ram UG5000W

Standard Operating Procedures3 pages

Questions and Answers

V
Valerie MullenAug 16, 2025
How to fix Uni-ram Ultrasonic Jewelry Cleaner when wash pump makes pumping sound but liquid does not flow?
- A
  Amber LarsenAug 16, 2025
  If the Uni-ram Ultrasonic Jewelry Cleaner's wash pump makes a pumping sound but liquid doesn't flow from the jets, there might be a few reasons. First, check if the drain valve is closed and open it by placing it in a vertical position. Second, the liquid level might be too low; ensure it's at least half full, up to 4 gallons (11 L). Finally, there could be debris in the pump or suction and output hose. In this case, follow Procedure 1, "Blocked Fluid Passage in Diaphragm pump".
K
Karen ConnerAug 19, 2025
Why Uni-ram Ultrasonic Jewelry Cleaner wash pump makes hissing sound and liquid does not flow?
- X
  xclarkAug 19, 2025
  If the Uni-ram Ultrasonic Jewelry Cleaner's wash pump makes a hissing sound but liquid does not flow, several issues could be the cause. First, water or contaminants may be in the air line of the pump, requiring you to follow Procedure 2, "Blocked Air Passage in Diaphragm Pump". Second, the flow control might be closed; loosen the locking nut on the control panel and rotate the control to the left to increase flow. Third, the liquid level could be too low; ensure it's at least half full, up to 4 gallons (11 L). Lastly, the brush could be clogged with debris; unthread the brush from the hose and operate the foot pedal. If free solvent flow is observed, replace the brush with PN 144-390S.
K
Kristopher MoralesAug 22, 2025
What to do if Uni-ram Ultrasonic Jewelry Cleaner brush pump does not make a noise and liquid does not flow?
- J
  Joseph ZamoraAug 22, 2025
  If the brush pump on your Uni-ram Ultrasonic Jewelry Cleaner isn't making noise and liquid isn't flowing when the pedal is depressed, it could be due to a couple of reasons. First, the foot pedal switch might not be functioning correctly; inspect it for free travel and lubricate it with gun oil. If the switch still doesn't move freely, replace it with PN 155-400BF2. Second, water in the air line could be causing the pump to stall; in this case, follow Procedure 2, "Blocked Air Passage in Diaphragm Pump".
J
Jay SantanaAug 25, 2025
Why Uni-ram UG5000W Ultrasonic Jewelry Cleaner solvent appears red or orange?
- M
  Matthew JonesAug 25, 2025
  If the wash solvent in your Uni-ram Ultrasonic Jewelry Cleaner appears red or orange, it's likely due to water in the solvent corroding the metal pail. To resolve this, replace or recycle the wash solvent.
S
Shannon OlsenAug 27, 2025
Why Uni-ram Ultrasonic Jewelry Cleaner guns not clean, wash solvent is milky white?
- J
  jessicagalvanAug 27, 2025
  If the wash solvent in your Uni-ram Ultrasonic Jewelry Cleaner is milky white and your guns aren't getting clean, it's likely that the wash solvent is contaminated with water. You should replace or recycle the wash solvent.
J
Jennifer DelacruzAug 30, 2025
Why Uni-ram Ultrasonic Jewelry Cleaner guns not clean, pump working, solvent flow normal?
- B
  Brenda BerryAug 30, 2025
  If the guns are not cleaning properly with your Uni-ram Ultrasonic Jewelry Cleaner, even though the pump is working and solvent flow is normal, consider these possibilities: Ensure the trigger is locked in the open position using Trigger Lock Spring PN 120-350. Verify the spray gun is correctly installed onto the nozzle with the proper adapter. Check that you're using a solvent formulated for the type of paint. Confirm that the air supply pressure is at 85 PSI.
P
Paul DyerSep 2, 2025
Why Uni-ram UG5000W inside wall of tank is coated with paint even though operator maintains tank?
- E
  erin21Sep 2, 2025
  If the inside wall of the tank in your Uni-ram Ultrasonic Jewelry Cleaner is coated with paint, even with regular maintenance, it suggests that the liquid lacks sufficient cleaning strength. Replace the solvent/water and AQUA-KLEEN in the pail. Consider using a solvent specifically formulated for the type of paint you're using and suitable for automatic spray gun cleaning.
J
Jeffrey Pham Jr.Sep 4, 2025
Why Uni-ram Ultrasonic Jewelry Cleaner clean rinse does not work?
- P
  Patrick HarrisSep 4, 2025
  If the clean rinse function on your Uni-ram Ultrasonic Jewelry Cleaner isn't working, it could be due to a couple of reasons. First, there might not be enough liquid in the clean rinse pail (right side), so add more liquid. Second, the rinse pump might be leaking from a crack caused by corrosion due to acidic or chlorine-contaminated solvent; if this is the case, replace the rinse pump with PN URP-100SF.
D
Darius OchoaSep 7, 2025
What to do if Uni-ram Ultrasonic Jewelry Cleaner wash pump does not stop unless timer is turned by hand?
- S
  Steven SnyderSep 7, 2025
  If the wash pump on your Uni-ram Ultrasonic Jewelry Cleaner doesn't stop unless the timer is turned by hand or the air is shut off, or if the wash pump doesn't start at all, the timer is likely defective. Replace the timer with PN 115-200K.
M
Mr. Jack PotterSep 10, 2025
What to do if Uni-ram Ultrasonic Jewelry Cleaner timer knob spins back when turned?
- D
  David LangSep 12, 2025
  If the timer knob on your Uni-ram Ultrasonic Jewelry Cleaner spins back when turned, the timer is defective and needs to be replaced with PN 115-200K.