Unidrive M200 - User Manual

Unidrive M200 /M201 Quick Start Guide 1
Issue Number: 1
This guide is intended to provide basic information required in order to set-up a drive to run a motor.
Please refer to the Unidrive M200 / M201 User Guide which is available to download from
www.controltechniques.com/userguides.
1 Safety information
2 Product information
2.1 Ratings
Unidrive M200, M201
Quick Start Guide
This guide does not include safety information. Incorrect installation or operation of the
drive, could cause personnel injury or equipment damage. For essential safety
information, please refer to the Unidrive M200 / M201 User Guide or the safety booklet
supplied with the drive.
Model
Input
phases
Max.
cont
input
current
Max input
fuse rating
Nominal cable size
Output current
European USA
1 Ph 3 Ph Input Output Input Output
Max.
cont
output
current
Nominal
power
Motor
power
ph A A A
mm
2
mm
2
AWG AWG A kW hp
01100017 1 10 1 1 16 16 1.7 0.25 0.33
01100024 1 16
1 1 14 16 2.4 0.37 0.5
01200017 1 6
1 1 16 16 1.7 0.25 0.33
01200024 1 6
1 1 16 16 2.4 0.37 0.5
01200033 1 10
1 1 16 16 3.3 0.55 0.75
01200042 1 16
1 1 16 16 4.2 0.75 1
02100042 1 18.8 20
2.5 1 12 16 4.2 0.75 1
02100056 1 24 25
4 1 10 16 5.6 1.1 1.5
02200024 1 / 3 5.3/4.1 6 6 1 1 16 16 2.4 0.37 0.5
02200033 1 / 3 8.3/6.7 10 10 1 1 16 16 3.3 0.55 0.75
02200042 1 / 3 10.4/7.5 16 10 1 1 16 16 4.2 0.75 1
02200056 1 / 3 14.9/11.3 20 15 2.5/1.5 1 12/14 16 5.6 1.1 1.5
02200075 1 / 3 18.1/13.5 20 15 2.5 1 12 16 7.5 1.5 2
02400013 3 2.4
6 1 1 16 16 1.3 0.37 0.5
02400018 3 2.9
6 1 1 16 16 1.8 0.55 0.75
02400023 3 3.5
61 116162.30.751
02400032 3 5.1
61 116163.21.11.5
02400041 3 6.2
10 1 1 16 16 4.1 1.5 2
03200100 1 / 3 23.9/17.7 25 20 4 1.5 10/12 14 10 2.2 3
03400056 3 8.7
10 1 1 14 16 5.6 2.2 3
03400073 3 12.2
16 1.5 1 12 16 7.3 3 3
03400094 3 14.8
16 2.5 1.5 12 14 9.4 4 5
04200133 1 / 3 25 20 4/2.5 2.5 10 12 13.3 3 3
04200176 3
25 4 2.5 10 12 17.6 4 5
04400135 3
20 2.5 2.5 10 12 13.5 5.5 7.5
04400170 3
25 4 2.5 10 12 17 7.5 10
The nominal cable sizes shown in the table above, are provided as a guide only. Ensure
that the cables used conform to the local wiring regulations.
WARNING
NOTE

Summary

Safety Information

General Safety Warning

Warning about potential injury or equipment damage due to incorrect installation or operation. Refers to user guide.

Product Information

Product Ratings Table

Table detailing model, input/output current, fuse rating, cable size, and power ratings.

Mechanical Installation

Terminal Cover Removal

Instructions on how to remove the terminal cover using a flat bladed screwdriver.

Recommended Torque Settings

Table specifying torque settings for different terminal blocks and model sizes.

Electrical Installation

Electrical Connection Diagram

Diagram showing electrical connections and available terminals on the drive.

Keypad and Display

Keypad and Display Overview

Explanation of the keypad layout, display, and functions of navigation and control keys.

Running the Motor

Pre-Power Up Checks

Ensures correct connections and signals are set before applying power to the drive.

Powering Up the Drive

Instructions for powering up the drive and checking initial display status.

Setting Speed Limits

Procedure for entering minimum and maximum speed parameters.

Setting Acceleration and Deceleration Rates

Procedure for entering acceleration and deceleration rate parameters.

Entering Motor Nameplate Details

Inputting motor's rated current, speed, voltage, and power factor for optimal performance.

Motor Autotune Procedure

Steps for performing stationary or rotating autotune, including parameter settings and signal requirements.

Saving Parameters

Instructions on how to save configured parameters using the 'SAVE' function.

Running and Stopping the Motor

Guide to starting, controlling speed, and stopping the motor using the drive's functions.

Unidrive M200 Specifications

General

Brand	Unidrive
Model	M200
Category	Media Converter
Language	English