Unipulse F701-C Manual

UNIPULSE F701-C 中文技术手册 无锡友波贸易有限公司 0510-82706452/13861775500
NET
ZERO
Lights when the weight value display is Net weight. Goes out when it is Gross
weight. 当重量之以净重显示时点亮
。当重量之以毛重称重时熄灭。
·
Lights at a true zero point (0±1/4 scale division). (When the 1/4 scale division
display is OFF under Function Selection in setting mode 3.) 在真实零点（0±1/4
分度值）时点亮 。
（当超过 0±1/4 分度值时熄灭，可在设定模式 mode
3 功能选择中设定。
）
·
Lights at a true zero point (0±1/4 scale division), and at the central point of the scale
interval of the indicated value (indicated value±1/4 X Min. Scale Division).(When
the 1/4 sc
ale division display is ON under Function Selection in setting mode 3.)
在真实零点（0±1/4 分度值）并处于指示值分段中心（指示值±1/4 X 最小分
度值） 时点亮 。
（当 0±1/4 分度值时点亮， 在设定模式 mode 3 中设定。
）
Flashes when the voltage of the lithium battery for memory backup has dropped.
Replac
e with a new battery. For the method of replacement, refer to
"I3.REPLACEMENT OF THE BACKUP BATTERY" on P. 162.
当备份存储电池电压不足时闪烁，应立刻更换新电池。更换方法可参考“第 162
页的 13. 备份电池更换”有关说明。
on the status display lights,
的点亮、熄灭、闪烁。
※ The expression
“ ”
in this instruction manu
al shows that
goes out, or flashes.
在本操作手册中表示状态指示灯
点亮
⑤Setting keys 设定键
When the
key is pressed, the Tare weight is displayed, and
flashes.
当按压 0 键时，显示皮重，
“皮重灯”闪烁。
0键
(When the Tare weight display with the
key is valid under Restriction on the
Tare Subtrac
tion Function in setting mode 4.) To go back to the weight display,
press the
key again. （当按压 0 键有效，显示皮重时，可在设定模式
mode 4 去皮功能限定选择中设定）再按一次 0 键，返回到称重显示状态。
~
Numerical keys to make settings.
数字键 数字键用于设定操作。
Function key to switch the setting mode.
功能键 功能键用于开关设定模式。
Change/Enter key to confirm setting items and setting values.
变更/确认键 变更/确认键是确认设定项目及设定值。
⑥Function keys （双）功能键
Key to perform one
-
touch Tare subtraction.
on the status display lights.(In
setting mode 0) However, Tare subt
raction is performed only in the following cases
皮重键
depending on the setting of Restriction on the Tare Subtraction Function in setting
（项目上翻）mode 4. “皮重键”是一键去皮确认键。 “皮重灯”点亮（设定模式 mode 0）
。
去皮功能仅在设定模式 mode 4 去皮功能限定的下列情形有效：
·
When the weight value is stable
(when "
'' is on). 重量值稳定
（ 点亮）
·
When the range of Tare subtraction is 0 < Tare
≤
Capacity.
去皮在允许范围，0 < 皮重≤ 传感器负荷
Use as an increment key for setting operation.“皮重键”也作为设定项目上翻键。
-5-

Unipulse F701-C Specifications

General

Brand	Unipulse
Model	F701-C
Category	Accessories
Language	English