Uponor T-167 User Manual

Climate Control Zoning System II installation and operation manual | Table of contents l i
Table of contents
Foreword ...................................iii
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Safety symbols .................................... iv
Safety measures ................................... iv
Power ........................................... iv
Technical constraints ............................... iv
Limitations for radio transmission ...................... iv
Compliance ....................................... iv
Proper disposal .................................... iv
Chapter 1: System overview ...................1
System example ................................... 1
System components ................................ 1
Base unit ......................................... 2
Main characteristics ............................... 2
Options ........................................ 2
Components .................................... 2
Thermostats ...................................... 3
Dial thermostats ................................... 3
Main characteristics ............................... 3
Components .................................... 3
Digital thermostats ................................. 3
Main characteristics ............................... 3
Components .................................... 3
Expansion module .................................. 4
Main characteristics ............................... 4
Components .................................... 4
Uponor actuators ................................... 4
On/off control .................................... 4
PWM control .................................... 4
Autobalancing ..................................... 4
Low hysteresis temperature .......................... 4
MicroSD card ..................................... 4
Chapter 2: Installation setup ...................5
Installation procedure ............................... 5
Installation preparation .............................. 5
Placement ...................................... 5
Installation example ................................ 6
Chapter 3: Installing the base unit ..............7
Placement ........................................ 7
Modular placement ............................... 7
Attaching and detaching components ................... 7
Installing the antenna ............................... 8
Attaching the antenna to a base unit ................. 8
Attaching the antenna to a wall ...................... 8
Connecting the antenna cable ...................... 8
Attaching the base unit to a wall ....................... 9
Mounting brackets ................................ 9
Screws and wall plugs ............................. 9
Connecting the expansion module (optional) ............. 9
Removing the expansion module ...................... 10
Connecting components to the base unit ................ 10
Connecting actuators to the base unit .................. 11
Connecting a circulation pump to the base unit ........... 11
Connecting a boiler (optional) ......................... 12
Connecting a boiler to the base unit .................... 12
Connecting the base unit to AC power .................. 12
Testing actuators ................................... 13
Chapter 4: Installing thermostats and sensors ....15
Thermostat placement .............................. 15
Labeling thermostats ................................ 15
Inserting batteries .................................. 15
Connecting an external sensor to a thermostat (optional) ... 15
Digital thermostats ................................. 16
Attaching a thermostat to a wall ..................... 16
Using a wall bracket (recommended) ................. 16
Using a screw and wall plug ........................ 16
Using an adhesive strip (not included) ................ 16
Attaching to a table stand .......................... 17
First setup of digital thermostats ....................... 17
Select thermostat control mode ..................... 17
Temperature setpoint ............................. 17
Registering thermostats in the base unit ................ 18
Finishing installation ................................ 19
Chapter 5: Operating the base unit ..............21
Sequence of operation .............................. 21
Normal operation ................................... 21
Run mode ........................................ 21
Exit to run mode ................................. 21
Resetting the base unit .............................. 21
Unregistering channels in the base unit ................. 21
Unregistering all channels ............................ 22
Chapter 6: Operating dial thermostats ...........23
Thermostat components ............................. 23
Adjusting the temperature ............................ 23
Replacing batteries ................................. 23
Factory reset ...................................... 24
Chapter 7: Operating digital thermostats .........25
Thermostat components ............................. 25
Display layout ..................................... 25
Operating buttons .................................. 26
Start up .......................................... 26
Adjusting temperature ............................... 26
Run mode ........................................ 26
Settings .......................................... 26
Sensor options .................................... 27
Adding a sensor ................................... 27
High oor temperature limitation ....................... 27
Low oor temperature limitation ....................... 28

Uponor T-167 Specifications

General

Brand	Uponor
Model	T-167
Category	Thermostat
Language	English