NAIL FILING SYSTEM
UP200C Series Controller
INSTRUCTION MANUAL
● We thank you for your purchasing our products.
● Please read this instruction before practical operation.
● Please keep this instruction close to the people who are
going to use the appliance.
1. APPLICATIONS
* To control the micro-motor handpiece only.
Not possible to be used for the other applications.
* For every nail filing (forming, buffing, sculptured, pierce drilling etc.)
Do not use the unit for the other applications.
2. PRECAUTIONS
* The following precautionary articles show how you operate our products
safe and right, which prevents you from any danger or damage before
happened.
* Never fail obeying to any article, in which crucial and important matters are
shown concerning safety.
This symbol indicates the possibility of being dead or
WARNING
wounded seriously for men if our products are
operated by mistake regardless of this instruction.
This symbol indicates the possibility of being hurt for
CAUTION
men or generating material damages if our products
are operated by mistake regardless of this
instruction.
2.1 Clothes while at work
WARNING
* Please work in due order. Knitted gloves, clothes with open cuffs and long
hairs are in danger of being caught in a machine.
CAUTION
* Please put goggles on not to enter dusts and grits into eyes. In addition,
please put a protection mask on not to inhale dusts and grits.
2.2 Safety Operation
WARNING
* Please use Appliances in a place where the temperature is from 0 to 40 ℃
and the relative humidity is from 20 to 80% (no dew condensation).
Please never use them in humid, wet places and outdoors in the rain.
It may invite electric shock or fire, weaken insulation and cause rust and
bad operation.
* Do not use absolutely in any place where there are flammable or explosive
materials such as lacquer, paints, thinner, gasoline, gas and adhesives.
* Also, ensure that there is no flammable and no corrosive gas areas.
* Please do not damage the AC cord and Motor Cord to prevent electric
leakage and shock or fire.
CAUTION
* Please work in a clean and full space and use Appliances in well orderly
areas not to stumble over cords.
* Please do not place a cloth or anything else on the ventilation slits of
Appliance. Also, please avoid using while any dust is attached around the
ventilation outlet.
* Please take care not to allow any alien substances such as water, oil, and
dust into Appliances.
* Please do not blow something like compressed air into ventilation slits of
Appliance.
* Please pull the AC plug out from the receptacle when not operated.
R
* Please keep Appliances in well dried areas.
* Please keep Appliances in a place not to be reached by Children.
* Please never make any modification, which may damage original
performance and safety.
* Please keep you from breaking down and adjusting the Appliance by
yourself.
2.3 Precautions while at work
WARNING
* Please never fail using Controller under the voltage indicated in the panel.
CAUTION
* Please stop the operation if any bad rotation or other abnormal movement
is found out while at work.
* Please ensure that any tool should be well chucked and after adjusting the
speed control knob on the controller to the left 「MIN」. After then, please
switch the power on and increase rotation speed gradually.
* Please take care not to drop Controller especially.
2.4 Maintenance and Inspection
* When dirt is found eminently, remove it with a cloth dipped in a detergent
solution in water and well wrung. After then, wipe with a dry duster.
* Periodical inspection is recommended every 1 or 2 years to use the
appliance safely and efficiently. Please consult your supplier for the service.
3. PARTS IDENTIFICATION / CONNECTION
① Power Switch ② Power Indicator ③ Speed Control Knob
④ Overload Indicator ⑤ Rotation Switch ⑥ Output Jack
⑦ Fuse/Fuse-holder
* Make it sure that each switch or knob on Controller should be on the
following positions:
POWER・・・・・・・・・・｢ OFF ｣
SPEED CONTROL ・・・・・｢ MIN ｣
* Connect the Handpiece to Output Jack．
* Ensure that the Power Switch is turned off before connecting the AC plug to
the power supply.
1 2
NO
FFO
MIN.
MADE IN JAPAN
INPUT
OUTPUT
12 KAWA RAI-CHO KUKI-SH I SAITAMA JAPAN
URAWA CORPORATION
AC120V 60Hz 23VA
DC 3V － 20V 0.5A
NO.MODEL UP201C
125V 1A
×××××
OVERLOAD
+-
OUTPUT
REVERSE
FORWARD
MAX.
SPEED CO NTROL
Motor Handpiece(Option)
R S
S
3 4 5 6 7
To Next Page
Need help?
General