Why is my US Water Systems Water Filtration System using too much salt?
Your US Water Systems Water Filtration System might be using too much salt due to an improper salt setting. Check the salt usage and salt setting to ensure they are correctly configured. Also, excessive water in the brine tank can cause this issue; refer to problem 7 for solutions related to excessive water in the brine tank.
How to fix loss of water pressure in my US Water Systems Water Filtration System?
A loss of water pressure in your US Water Systems Water Filtration System can occur due to several reasons. Iron buildup in the line to the water conditioner can restrict flow, so clean the line. Similarly, iron buildup within the water conditioner itself can cause this issue; clean the control, add a mineral cleaner to the mineral bed, and increase the frequency of regeneration. Also, check if the inlet of the control is plugged due to foreign material dislodged from pipes during plumbing work; remove the piston and clean the control.
What to do if US Water Systems Water Filtration System softener fails to draw brine?
If your US Water Systems Water Filtration System softener isn't drawing brine, start by checking the drain line flow control to see if it's plugged and clean it if necessary. Also, inspect the injector for any blockages and clean it. A plugged injector screen can also prevent brine draw, so clean the screen. Ensure that the line pressure isn't too low; increase it to 20 P.S.I. An internal control leak may be the cause, so consider changing the seals, spacers, and piston assembly. Finally, verify that the service adapter cycled; check the drive motor and switches.
What causes a US Water Systems Water Filtration System to fail to regenerate?
A US Water Systems Water Filtration System might fail to regenerate for a few reasons. First, check that the electrical service to the unit hasn't been interrupted; ensure permanent electrical service by checking the fuse, plug, pull chain, or switch. If the electrical supply is fine, the control itself might be defective and need replacement. Lastly, a power failure can prevent regeneration; reset the time of day on the unit.
How to stop continuous drain flow in my US Water Systems Water Filtration System?
Continuous drain flow in your US Water Systems Water Filtration System may be due to the valve not programming correctly. Check the control program and positioning of the control. If it's not positioning properly, replace the power head assembly. Foreign material in the control can also cause this; remove the power head assembly, inspect the bore, remove any foreign material, and check the control in various regeneration positions. An internal control leak can also lead to continuous drain flow, so replace the seals and piston assembly.
What causes excessive water in the brine tank of my US Water Systems Water Filtration System?
Excessive water in the brine tank of your US Water Systems Water Filtration System can be caused by several issues. A plugged drain line flow control can be the culprit, so clean the flow control. Alternatively, a plugged injector system might be the cause, so clean the injector and screen. If the timer isn't cycling, consider replacing it. Foreign material in the brine valve or brine line flow control can also lead to this problem, so replace the brine valve seat and clean the valve, and clean the brine line flow control.
Why does my US Water Systems Water Filtration System have iron in the conditioned water?
Iron in the conditioned water from your US Water Systems Water Filtration System is often due to a fouled mineral bed. Check the backwash, brine draw, and brine tank fill. You may need to increase the frequency of regeneration and the backwash.
How to fix mineral loss through the drain line of my US Water Systems Water Filtration System?
Mineral loss through the drain line in your US Water Systems Water Filtration System can be attributed to a couple of reasons. Air in the water system might be the cause; ensure that the well system has a proper air eliminator control and check for a dry well condition. Another potential cause is an improperly sized drain line flow control; check for the proper drain rate.
What to do if my US Water Systems Water Filtration System control cycles continuously?
If the control of your US Water Systems Water Filtration System cycles continuously, it could be due to a misadjusted, broken, or shorted switch. Determine if the switch or timer is faulty and replace it, or replace the complete power head.
What to do if my US Water Systems Water Filtration System has hard water?
If you're experiencing hard water with your US Water Systems Water Filtration System, several factors could be the cause. First, ensure the bypass valve is closed. Also, check the brine tank and add salt, maintaining the salt level above the water level. A plugged injector screen can also cause hard water, so clean the injector screen. Insufficient water flowing into the brine tank can be another reason; check the brine tank fill time and clean the brine line flow control if it's plugged. If you have a hot water tank, repeated flushing might be required to address hot water tank hardness. A leak at the distributor tube can also lead to hard water; inspect the distributor tube for cracks and check the O-ring and tube. Finally, an internal valve leak could be the problem; consider replacing ...
Comply with codes, handle tank carefully, use correct transformer, and use proper salt type.
Avoid freezing, direct sunlight, and ensure proper grounding and lead-free solder.
Gather channel locks, screwdriver, Teflon tape, wrenches, and recommended piping materials.
Ensure grounded outlet access, protect from weather, and avoid direct sunlight.
Lubricate O-rings, attach the control valve to the tank, and hand-tighten securely without tools.
Install bypass valve and connectors, lubricating O-rings and securing with clips.
Ensure bypass set, turn on water, flush air, and initiate manual regeneration for backwashing.
Advance to rinse, ensure clear water, allow refill, and add water to the brine tank.
General| Brand | US Water Systems |
|---|---|
| Model | Fusion |
| Category | Water Dispenser |
| Language | English |
To Next Page
