UTC Fire and Security EST SIGA-CC1 - User Manual

SIGA-CC1 Single Input Signal Module
Installation Sheet
Description
The SIGA-CC1 Single Input Signal Module is an addressable
module that is used to connect the following circuits:
• Audible and visible notification appliance circuits
(synchronized or unsynchronized)
• Speaker circuits
• Two-way telephone communication circuits (three-state or
four-state)
Upon command from the loop controller, the module connects
supervised Class B signal or telephone circuits to the
respective riser input. The riser input can be 24 VDC (to
operate polarized audible and visible signal notification
appliances), 25 or 70 VRMS (to operate audio evacuation
speakers), or firefighter telephones.
The module does not provide signal synchronization. To meet
UL 864 requirements for horn and strobe signal
synchronization, you must install a Genesis Signal Master
module.
The SIGA-CC1 module requires one address on the signaling
line circuit (SLC). Addresses are assigned electronically. There
are no address switches.
Diagnostic LEDs provide visible indication of the state of the
module through the cover plate:
• Normal: Green LED flashes
• Alarm/active: Red LED flashes
Personality codes
Use the personality codes described below to configure the
SIGA-CC1 module. See Table 1 for listing information
Table 1: Personality code listing information
Code
Description UL 864 CAN/ULC-
S527
EN 54-18
5
Signal - supervised
output (Class B)
  
6
Telephone - three-state
(Class B)
26
Telephone - four-state
(Class B)
 
Personality code 5: Signal - supervised output (Class B).
Configures the SIGA-CC1 module as a riser selector for
audible and visible notification appliance circuits or for
single-channel audio circuits. The output circuit is monitored for
open or shorted wiring. If a short exists, the module will not
activate in order to prevent shorting the riser. The module will
activate once the short is cleared.
Personality code 6: Telephone - three-state (Class B).
Configures the module as a riser selector for a three-state
firefighter telephone. When a telephone handset is plugged
into its jack or lifted from its hook, the module generates its
own ring-tone signal, making a separate ring-tone riser
unnecessary. The module sends this signal to the control panel
to indicate the presence of an off-hook condition, and waits for
the system operator to respond to the call. When the system
operator responds, the ring-tone signal is disabled.
Personality code 26: Telephone - four-state (Class B).
Configures the module as a riser selector for a four-state
firefighter telephone. Operation is the same as Personality
code 6 except that the module can distinguish when a
telephone is off-hook and when the circuit is shorted, which
causes a trouble condition.
Installation
Install this device in accordance with applicable national and
local codes, ordinances, and regulations.
Notes
• The module is shipped from the factory as an assembled
unit; it contains no user-serviceable parts and should not
be disassembled.
© 2015 UTC Fire & Security Americas Corporation, Inc. 1 / 6 P/N 387022P-EN • REV 12 • ISS 22JUN15

Summary

Personality Codes

Personality Code 5: Signal - Supervised Output (Class B)

Configures module as riser selector for notification appliance circuits or single-channel audio.

Personality Code 6: Telephone - Three-State (Class B)

Configures module as riser selector for three-state firefighter telephone.

Personality Code 26: Telephone - Four-State (Class B)

Configures module as riser selector for four-state firefighter telephone.

Installation

Module Installation Steps

Steps for installing the SIGA-CC1 module, including wiring and mounting.

Protection from Transient Spikes

Guidance on installing a bipolar transient protector for inductive loads.

Wiring

General wiring notes, riser wiring notes, and module wiring instructions.

Wiring Diagrams

NAC Wiring (Personality Code 5)

Diagram for connecting notification appliance circuits with personality code 5.

Audio Wiring (Personality Code 5)

Diagram for connecting audio circuits with personality code 5.

Telephone Wiring (Personality Codes 6 & 26)

Diagrams for three-state and four-state telephone circuits.

Specifications and Regulatory Information

Technical Specifications

Details on operating voltage, current, impedance, output ratings, and electrical box requirements.

Regulatory Information

Includes manufacturer, FCC compliance, North American standards, and EU compliance details.

UTC Fire and Security EST SIGA-CC1 Specifications

Power

operating voltage range	15.20 to 19.95 VDC
standby current	310 µA
activated current	135 µA

Output Ratings

output voltage for special applications	24 VDC
output current for special applications	2 A
audio output 25 VRMS	50 W
audio output 70 VRMS	35 W

Line and Circuit Specifications

maximum line impedance	Refer to the control panel installation manual
ground fault impedance	10 kΩ
EOL resistor value	47 kΩ

Dimensions and Sizes

minimum box size	3.5 × 3.5 × 1.5 in. (85 × 85 × 38 mm)
compatible electrical box depth	2-1/2 in. (64 mm)
wire sizes	12 to 18 AWG (1.0 to 4.0 mm²)

Operating Environment

operating temperature range	32 to 120°F (0 to 49°C)
relative humidity	0 to 93%, noncondensing
storage temperature range	−4 to 140°F (−20 to 60°C)