UTILEV UT30P - Page 52



4646
（（
99
））
Start the engine, check for oil leaks around oilStart the engine, check for oil leaks around oil
pug and filter.pug and filter. If the leak is excessive, the part was notIf the leak is excessive, the part was not
installed corrinstalled correctlyectly..

（（
1010
））
Warm-up engine, then shut-off and check oilWarm-up engine, then shut-off and check oil
level. Fill if needed. To check the oil fluid level, placelevel. Fill if needed. To check the oil fluid level, place
truck on level ground.truck on level ground.
2. Apply lubricant to front and rear of pin roll of2. Apply lubricant to front and rear of pin roll of
tilt cylindertilt cylinder
Wipe any overflow clean.Wipe any overflow clean.
3. Check the gear oil of drive axle housing3. Check the gear oil of drive axle housing
Change the oil after 200 hours. Change moreChange the oil after 200 hours. Change more
frequently if operating truck in a dusty environment.frequently if operating truck in a dusty environment.
4. Change transmission fluid filter (first time,4. Change transmission fluid filter (first time,
then then semi-annuasemi-annually)lly)
Check Check the the hydraulic hydraulic transmission transmission fluid. fluid. ReplaceReplace
fluid if it appears to be contaminated.fluid if it appears to be contaminated.
Put the truck on level ground, lower forks to the floor,Put the truck on level ground, lower forks to the floor,
tilt the mast back, apply parking brake, puttilt the mast back, apply parking brake, put
transmission in neutral position, and shut off engine.transmission in neutral position, and shut off engine.
!! WWaarrnniinngg
：：

Hot hydraulic oil and parts may causeHot hydraulic oil and parts may cause
injuryinjury. DO NOT touch the hot h. DO NOT touch the hot hydraulic oil orydraulic oil or
parts.parts.
（（
11
））
Detach the rubber washer and the frontDetach the rubber washer and the front
baseplate.baseplate.
（（
22
））
Detach Detach the the filter. filter. Handle Handle according according to to locallocal
regulations.regulations.
（（
33
））
Wipe the filter Wipe the filter base clean. base clean. Confirm that the Confirm that the oldold
washer on the base has been thoroughly removed.washer on the base has been thoroughly removed.
（（
44
））
Apply small amount hydraulic fluid on the newApply small amount hydraulic fluid on the new
filter element washer.filter element washer.
（（
55
））
Install filter by hand. When the filter get toInstall filter by hand. When the filter get to
pedestal, screw down an additional 1/2-3/4 turn.pedestal, screw down an additional 1/2-3/4 turn.
5. Change hydraulic transmission oil (first time,5. Change hydraulic transmission oil (first time,
then then semiannuasemiannually)lly)
Park truck on level ground, lower the forks to thePark truck on level ground, lower the forks to the
ground and tilt the mast back. Engage the parkingground and tilt the mast back. Engage the parking
brake, put transmission in neutral position, and turn offbrake, put transmission in neutral position, and turn off
engine.engine.
!! WWaarrnniinngg
：：

Hot hydraulic oil and parts Hot hydraulic oil and parts will causewill cause
injuryinjury. DO NOT the hot hydraulic oil a. DO NOT the hot hydraulic oil and parts.nd parts.
（（
11
））
Put one case (volume is over 20 liters) under thePut one case (volume is over 20 liters) under the
transmission.transmission.
（（
22
））
Remove oil plug and drain oil.Remove oil plug and drain oil.
（（
33
））
Clean oil plug then install.Clean oil plug then install.
（（
44
））
Take out the dipstick. Add hydraulic oil. SeeTake out the dipstick. Add hydraulic oil. See
《《
Forklift Truck Fluid Use ChartForklift Truck Fluid Use Chart
》》
..
https://www.forkliftpdfmanuals.com/