V-ZUG 74A - Energy Saving; Adjust Time; Auto-Start; Auto-Off (Standby)

18
Alternatively, hold the P / ESC button (B7) down for 10 seconds.
The languages scroll through.
Hold the OK button (B4) down for 5 seconds to conrm. The ap-
pliance goes o.
Energy Saving
Use this function to enable or disable Energy Saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To enable or disable the function, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “ENERGY
SAVING” is displayed;
3. Press the OK button (B4). “DISABLE?” is displayed (or “ENA
BLE?” if the function has already been disabled).
4. Press the OK button (B4) to enable or disable the function
or the P / ESC button (B7) to exit the menu.
Please note: A few seconds may elapse between
“ENERGY SAVING ENABLED” mode and delivery of the rst
drink; “PREPARATION UNDERWAY” is displayed.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “ADJUST
TIME” is displayed;
3. Press the OK button (B4). The hours ash on the display;
4. Press the ▽ and △ buttons (B5 and B6) to change the
hours;
5. Press the OK button (B4) to conrm. The minutes ash on
the display;
6. Press the ▽ and △ buttons (B5 and B6) to change the
minutes;
7. Press the OK button (B4) to conrm;
8. Press the P / ESC button (B7) to exit the settings menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note:
To enable this function, the time must be set correctly.
To enable Auto-on, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “AUTO
START” is displayed;
3. Press the OK button (B4). “ENABLE?” is displayed;
4. Press the OK button (B4). The hours ash on the display;
5. Press the ▽ and △ buttons (B5 and B6) to choose the
hours;
6. Press the OK button (B4) to conrm. The minutes ash on
the display;
7. Press the ▽ and △ buttons (B5 and B6) to change the
minutes;
8. Press the OK button (B4) to conrm. “ENABLED” appears
under “AUTOSTART”.
9. Press the P/ ESC button (B7) to exit the menu.
To disable the function:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “AUTO
START” is displayed;
3. Press the OK button (B4). “DISABLE?” is displayed;
4. Press the OK button (B4) to conrm;
5. Press the P/ ESC button (B7) to exit the menu. “DISABLED” is
displayed.
Auto-o (Standby)
The appliance is set by default to go o if not used for two
hours.
The time can be changed so that the appliance switches o after
15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-o, proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “AUTOOFF”
is displayed;
3. Press the OK button (B4);
4. Press the ▽ and △ buttons (B5 and B6) until the required
time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button (B4) to conrm;
6. Press the P/ ESC button (B7) to exit the menu.
Auto-o is programmed.
Setting the temperature
To modify the temperature of the water used to make the coee,
proceed as follows:
1. Press the P / ESC button (B7) to enter the settings menu.
2. Press the ▽ and △ buttons (B5 and B6) until “SET TEMPE
RATURE” is displayed;
3. Press the OK button (B4);
4. Press the ▽ and △ buttons (B5 and B6) until the required
temperature is displayed (l = low, llll = high);
5. Press the OK button (B4) to conrm;
6. Press the P/ ESC button (B7) to exit the menu.
Setting water hardness
The operating period can be extended if required, making desca-