VADDIO DocCAM 20 HDBT User Manual (English)

Other manuals for VADDIO DocCAM 20 HDBT

Integrator's Complete Guide70 pages

Configuration And Administration Guide41 pages

Using Instruction5 pages

Questions and Answers:

S
Samantha HolmesAug 17, 2025
What to do if VADDIO DocCAM 20 HDBT is not responding?
- D
  Daniel PetersAug 18, 2025
  If your VADDIO Document Camera isn't responding, with no status light, video, or response to the remote, here's what to check: * First, ensure the camera is receiving power from its source (OneLINK device or PoE+ injector) and that the cable is securely connected. If power is confirmed, the cable or the camera itself might be faulty. * If the status light is off, the camera might be in standby mode. Try pointing the remote at the camera and pressing the Power button. * Also, the remote might not be using the same IR channel as the camera. Press the Camera Select 1 button on the remote, and try the other Camera Select buttons if needed. * Finally, the camera might be confused and needs a reboot. Try rebooting or power-cycling the camera.
S
Steven AllenAug 20, 2025
Why VADDIO Document Camera does not respond to the remote?
- D
  donna29Aug 20, 2025
  If your VADDIO Document Camera isn't responding to the remote, but the web interface is accessible, the issue might be: * The remote and camera are not using the same IR channel. Try pressing the Camera Select 1 button on the remote, or other Camera Select buttons. * IR is switched off. Turn IR on via the System page, DIP Switches tab. * The remote's batteries are dead. Replace the batteries in the remote.
T
Tracy MoralesAug 23, 2025
How to fix VADDIO DocCAM 20 HDBT when it never finishes initializing?
- D
  Donald CruzAug 23, 2025
  If your VADDIO Document Camera never finishes initializing and the light is purple, this indicates that the camera is not receiving enough power. Use PoE+ instead of PoE, as PoE does not deliver sufficient power.
N
Natasha RiveraAug 26, 2025
What to do if VADDIO DocCAM 20 HDBT Document Camera does not respond to the remote and the light is yellow?
- J
  Jason HigginsAug 26, 2025
  If your VADDIO Document Camera is not responding to the remote and the light is yellow, this indicates that a firmware update is in progress. Wait a few minutes, and try again when the light turns blue.
J
John JordanAug 28, 2025
What to do if VADDIO DocCAM 20 HDBT responds to the remote but the web interface is not available?
- K
  Katherine PerezAug 28, 2025
  If the VADDIO Document Camera responds to the remote but the web interface is unavailable, the camera might not be using the IP address you are browsing to. Press the Data Screen button on the remote to see camera information.
W
William SharpAug 30, 2025
How to troubleshoot VADDIO DocCAM 20 HDBT not responding to RS-232 commands?
- K
  Kimberly MartinAug 30, 2025
  If the VADDIO Document Camera's web UI is available but the camera does not respond to commands sent via RS-232 connection to the OneLINK device, consider the following: * The RS-232 cable to the OneLINK device may not be connected, or could be faulty. Connect a known good cable. * The camera's baud rate setting might not match the settings on the controlling device. Check the baud rate setting at both ends to ensure they match. The camera's baud rate setting is available on the System page in the web UI.
A
Amanda PalmerSep 1, 2025
How to enable H.264 video stream on VADDIO Document Camera?
- M
  Michele GreenSep 1, 2025
  If there is no H.264 video stream from your VADDIO Document Camera, ensure that streaming is enabled on the Streaming page in the web interface.
W
Wanda StarkSep 4, 2025
Why is the laser pointer off-center in VADDIO DocCAM 20 HDBT Document Camera?
- C
  Cody HancockSep 4, 2025
  If the laser pointer is off-center in the image area of your VADDIO Document Camera, the laser pointer is out of alignment. Contact Vaddio Technical Support.
D
destiny69Sep 6, 2025
What to do if VADDIO Document Camera does not respond to the remote but the web interface is available?
- D
  Dawn AndersonSep 7, 2025
  If your VADDIO Document Camera isn't responding to the remote, but the web interface is accessible, here are a few things to check: * Ensure the remote and camera are using the same IR channel by pressing the Camera Select 1 button on the remote. If needed, try the other Camera Select buttons. * Verify that IR is enabled in the system settings (System page, DIP Switches tab). * Replace the remote's batteries with new ones.
D
Debra WalkerSep 12, 2025
Why VADDIO Document Camera never finishes initializing and the light is purple?
- K
  Kimberly WilsonSep 12, 2025
  If your VADDIO Document Camera never finishes initializing and the status light is purple, it might not be receiving enough power. Try using PoE+ instead of PoE, as PoE may not deliver sufficient power.

VADDIO DocCAM 20 HDBT Specifications

General

Brand	VADDIO
Model	DocCAM 20 HDBT
Category	Document Camera
Language	English

VADDIO DocCAM 20 HDBT Installation Guide

Table of Contents

Other manuals for VADDIO DocCAM 20 HDBT

Questions and Answers:

VADDIO DocCAM 20 HDBT Specifications