Vanderbilt SPC5330.320 - Flexc Commands

402 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

24 Notes

© Vanderbilt 2018 400 A6V10276959-d

11.2018

Table of Contents

Default Chapter3
- Table of Contents3
1 Meaning of Symbols10
2 Security11
- Target Group11
- General Safety Instructions11
- Meaning of Written Warning Notices and Hazard Symbols12
  - Warning Notices12
  - Hazard Symbols13
3 Directives and Standards14
- EU Directives14
- Overview of Conformity to EN50131 Standard14
  - Compliance with EN50131 Approvals20
- Compliance with en 50136-1:2012 and en 50136-2:201422
- Compliance with INCERT Approvals22
- PD 6662:2010 Conformance Guidelines23
- Compliance with Vds Approvals28
- Compliance with NF and A2P Approvals29
4 Technical Data31
- Spc400031
- Spc500033
- Spc600037
- Spcp355.30040
5 Introduction42
6 Mounting System Equipment43
- Mounting a G2 Housing43
- Mounting a G3 Housing44
  - Mounting a Back Tamper Kit46
  - Battery Installation for EN50131 Compliance50
- Mounting a G5 Housing51
- Mounting a Keypad56
- Mounting an Expander56
7 Smart PSU57
- SPCP355.300 Smart PSU57
8 Controller Hardware68
- Controller Hardware 42Xx/43Xx/53Xx/63Xx68
- Controller Hardware SPC5350 and 635070
9 Door Expander74
10 Wiring the System75
- Wiring the X-BUS Interface75
- Wiring of Branch Expander83
- Wiring the System Ground84
- Wiring the Relay Output84
- Wiring the Zone Inputs85
- Wiring an External SAB Bell88
- Wiring an Internal Sounder89
- Wiring Glassbreak89
- Installing Plug-In Modules90
11 Powering up the SPC Controller92
- Powering from Battery Only92
12 Keypad User Interface93
- Spck420/42193
- Spck620/62399
13 Software Support Tools105
14 Starting the System106
- Engineer Modes106
  - Engineer Pins106
- Programming with the Keypad106
- Configuring Start-Up Settings107
- Creating System Users108
- Programming the Portable ACE109
- Configuring Wireless Fob Devices110
  - Clearing Alerts Using the Fob110
15 Soft Engineer Programming Via the Keypad111
16 Engineer Programming Via the Keypad112
- System Status112
- Options113
- Timers117
- Areas121
- Area Groups123
- X-Bus123
  - X-BUS Addressing123
  - XBUS Refresh124
  - Reconfigure124
  - Keypads/Expanders/Door Controllers125
  - Addressing Mode133
  - XBUS Type134
  - Bus Retries134
  - Comms Timer135
- Users135
  - Add135
  - Edit135
  - Delete138
- User Profiles138
  - Add138
  - Edit138
  - Delete139
- Wireless140
  - Select a Wireless Programming Option141
  - One-Way Wireless142
  - Two-Way Wireless146
- Zones149
- Doors149
- Outputs153
  - Outputs Types and Output Ports154
- Communication158
  - Serial Ports158
  - Ethernet Ports158
  - Modems159
  - Central Station161
  - SPC Connect PRO163
- Test163
  - Bell Test163
  - Walk Test163
  - Zone Monitor164
  - Output Test165
  - Soak Test165
  - Audible Options165
  - Visual Indicators166
  - Seismic Test166
- Utilities166
- Isolate167
- Event Log167
- Access Log167
- Alarm Log167
- Change Engineer Pin168
- Sms168
  - Add169
  - Edit169
  - Delete170
- X-10170
- Set Date/Time170
- Installer Text171
- Door Control171
- SPC Connect171
17 Engineer Programming Via the Browser173
- System Information173
- Ethernet Interface173
- Connecting to the Panel Via USB175
- Logging into the Browser177
- SPC Home178
- Panel Status180
- Logs195
- Users197
- Wireless211
  - One-Way Wireless212
  - Two-Way Wireless222
- Configuration231
- Configuring Communications298
- File Operations343
  - File Upgrade Operations343
  - File Manager Operations347
18 Accessing Web Server Remotely349
- PSTN Connection349
- GSM Connection351
19 Intruder Alarm Functionality354
- Financial Mode Operation354
- Commercial Mode Operation354
- Domestic Mode Operation355
- Full and Local Alarms355
20 System Examples and Scenarios357
- When to Use a Common Area357
21 Seismic Sensors359
- Seismic Sensor Testing360
22 Blocking Lock Operation363
- Blocking Lock363
- Authorized Setting of the Blocking Lock364
- Locking Element365
23 Appendix367
- Network Cable Connections367
- Controller Status Leds368
- Powering Expanders from the Auxiliary Power Terminals369
- Calculating the Battery Power Requirements370
- Domestic, Commercial and Financial Mode Default Settings372
- Wiring of the X10 Interface373
- SIA Codes374
- CID Codes379
- Overview of Keypad Types381
- User PIN Combinations382
- Duress Pins382
- Automatic Inhibits382
  - Zones382
  - Access Pins383
  - Engineer Access383
  - Keypad User Logoff383
- Wiring of Mains Cable to the Controller383
- Maintenance Controller383
- Maintenance Smart PSU384
- Zone Types385
- Zone Attributes390
- Applicable Attributes to Zone Types393
- ATS Levels and Attenuation Specifications394
- Supported Card Readers and Card Formats394
- SPC Support for E-Bus Devices396
  - Configuring and Addressing E-Bus Devices397
- Flexc Glossary399
- Flexc Commands400
- ATS Category Timings403
- ATP Category Timings404
24 Notes406

Related product manuals

Vanderbilt SPC53 Series

Vanderbilt SPC6350

Vanderbilt SPC6330.320

Vanderbilt SPCP333.300

Vanderbilt SPCA210.100

Vanderbilt SPCP332.300

Preview: Vanderbilt SPC42 Series

Vanderbilt SPC42 Series