EXTENSION CORD SELECTION
R
eplace damaged extension cords immediately. Use of damaged extension cords can shock, burn or
electrocute.
If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage
drop which will cause loss of power and possible motor damage. A table of recommended extension
cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts for 115
volts at 150% of rated amperes. If an extension cord is to be used outdoors it must be marked with the
suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable
for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
LLeennggtthh ooff CCoorrdd iinn FFeeeett
115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
0-2A 18 18 18 16 16 14 14 12 12
2-3A 18 18 16 14 14 12 12 10 10
3-4A 18 18 16 14 12 12 10 10 8
4-5A 18 18 14 12 12 10 10 8 8
5-6A 18 16 14 12 10 10 8 8 6
6-8A 18 16 12 10 10 8 6 6 6
8-10A 18 14 12 1088664
10-12A 16 14 10 8 8 6 6 4 4
12-14A 16 12 10 866642
14-16A 16 12 10 8 6 6 4 4 2
16-18A 14 12 8 8 6 4 4 2 2
18-20A 14 12 8 6 6 4 4 2 2
SPECIFICATIONS
Amps: . . . . . . . . . . . . . . . . . . . . . . . . . . .0.92
Volts: . . . . . . . . . . . . . . . . . .120VAC ~ 60HZ
Free Speed: . . . . . . . . . . . . . . . . .3,000 RPM
10” RANDOM ORBITAL BUFFER FEATURES
1. Motor housing
2. ON/OFF Switch
3. Handles
4. Foam backing pad
5. Terrycloth bonnet
6. Synthetic wool polishing bonnet
SAFETY RULES FOR RANDOM ORBITAL BUFFERS
1
.
K
NOW YOUR POWER TOOL.
R
ead instruction manual carefully.
2.
ACCESSORIES MUST BE RATED FOR AT LEAST THE SPEED RECOMMENDED ON
THE TOOL WARNING LABEL.
Wheels and other accessories running over rated speed can fly apart
and cause injury.
3.
HOLD TOOL BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPER-
ATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN
CORD. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the
operator.
4. INSURE THAT THE TOOL IS DISCONNECTED FROM THE POWER SOURCE AND
THAT THE SWITCH IS IN “OFF” POSITION before replacing or adjusting the bonnet.
5. USE PROPER SAFETY EQUIPMENT. Wear safety goggles to protect your eyes and wear a pro-
tective mask to minimize breathing in the fine dust created while sanding. NOTE: Some wood contains
preservatives which can be toxic. Take extra care to prevent inhalation and skin contact when working
with these materials.
6.
SANDING OF LEAD-BASED PAINT IS NOT RECOMMENDED. Lead based paint should only
be removed by a professional.
7.
RAGS, CLOTHS, CORD, STRING AND THE LIKE SHOULD NEVER BE LEFT AROUND
THE WORK AREA.
8. ALWAYS USE BOTH HANDS TO OPERATE THE TOOL.
9. ALWAYS START AND STOP THE ORBITAL BUFFER ON OR AGAINST THE SURFACE
BEING POLISHED.
10. WARNING: There are certain applications for which this tool was designed. Star
Asia-USA, LLC strongly recommends that this tool NOT be modified and/or used for
any application other than for which it was designed. If you have any questions relative to its
application DO NOT use the tool until you have written Star Asia-USA, LLC and we have advised you.
Technical Service Manager
Star Asia-USA, LLC
P
.O. Box 58399
Renton, WA 98058-1369
76
1
3
4
56
3
2
To Next Page
Loading...