INTELLIGENT 8 SLOTS AA/AAA Battery Charger Product Instruction
Model No.: VTE8000
8 Slots Mix Charging -- LCD Display --
Worldwide Use- Super Fast Charger
Powered by Car Adaptor (optional) &
External AC Adaptor (Input: 100-240V
AC) for worldwide use.
Interchangeable plugs available
(optional).
BLUE BACKLIGHT LCD, 5 LEVELS
CHARGING STATUS.
Your AA/AAA Battery Charger is designed to charge
Vapex’Tech NiMH rechargeable batteries rated to
2900mAh(AA) or 1100mAh (AAA). The batteries will be
fully-charged by Microprocessor-Control System in 1~5 hours
for AA/AAA batteries. You can change 1/2/3/4/5/6/7/8
AA/AAA NiMH batteries simultaneously.
SAVE THESE INSTRUCTIONS
CHARGER FEATURES INCLUDE:
Specially designed with BLUE BACKLIGHT Electric LCD
display to indicate the charging status, 5 LEVELS.
Recharges 1 piece to 8 pieces of AA & AAA
Ni-MH batteries at a time.
Powered by the supplied Switching mode AC Adaptor
when using at indoor or by the supplied DC Car Adaptor
when using in a vehicle (optional).
Microprocessor Controlled – Batteries life well protected
by negative delta V cut-off function and timer protection.
Non-rechargeable battery detection.
Automatic trickle charge after full charge,
CURRENT-50mA
BLUELIGHT LCD indicator:
Large size LCD display for charging status
Charging: Empty battery icon;
Full charge: Full battery icon;
Wrong battery: Flashing full battery icon
LCD Displays the charging Levels
Safety Features :
+ΔV, -ΔV, 0ΔV cut-off function
Safety timer to prevent over charge
Reverse-polarity protection
Bad cell Detection
OPERATION INSTRUCTIONS:
1. Insert 1 to 8 pieces of AA/AAA rechargeable Ni-MH
batteries into the battery compartment.
2. Make correct contact for polarity (+ and –); according
to the sign in the battery compartment.
3. For Using in indoor
Connect the supplied AC adaptor’s barrel plug into the
jack on the back of the charger. Plug the AC adaptor
into household electric outlet. The switching power
supply will adjust automatically.
Caution: The supplied AC adaptor supplies 18VDC
and delivers 500mA, and its plug fits into the charger’s
DC input jack. Using an adaptor that does not meet
these specifications could damage the charger or the
adaptor.
When using in a vehicle
Connect the supplied DC car adaptor’s barrel plug into
the charger’s DC input jack. Plug the large end of the
cord into the 12V car lighter power port
4. Plug the charger into a correct house-hold electric
outlet.
5. The LCD will flash to check the charge status of the
batteries, after 10 seconds or so, LCD display will
indicate charging status, such as ‘Charging’, ‘Full
Charge’ or ‘Wrong battery’, and LCD display will also
show the charging levels of each cell, such as from
Empty icon, one segment, two segment to full icon.
After full charge, the LCD display will stay on Full Icon,
charge current turns to trickle current of 50mA each.
And the backlight will be always light till full charge.
6. Unplug the charger and remove the batteries from the
charger when not in use.
7. Begin against step 1 to charge the next set of batteries.
Bad Cell Detection:
When charge process is started, the charger detects the
health status of each of the cells in the battery compartment.
If any battery is unsuitable for charging the status LCD will
show flashing full battery icon.
Charging Current:
The total eight charging channels are divided into two parts
equally, 4 on left or right. The charging current would be
varied while different number of batteries placing on the
compartment. Please find the output current as follows.
Charging time:
*Charge time will vary depending upon the brand, capacity
and condition of batteries being charged.
Specifications of AC Adaptor:
To Next Page
Need help?
General
